Details, datasheet, quote on part number: TFS70S
PartTFS70S
CategoryTiming Circuits => SAW Devices (Surface Acoustic Wave)
TitleSAW Devices (Surface Acoustic Wave)
DescriptionApplication = Bandselective Repeater, Cellular ;; Center Frequency = 70.0 MHZ ;; 3 DB = 10.8 MHZ ;; Pass Band Ripple = 1.0dB ;; Insertion Loss = 24.0dB ;; Group Delay Ripple = 200ns ;; Package = 35 MM X 20 MM Dip
CompanyVectron International
DatasheetDownload TFS70S datasheet
  

 

Features, Applications

Ambient temperature TA: Input power level: Terminating impedances in fc:

Remark: Reference level for the relative attenuation arel of the TFS 70S is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The reference frequence fc is the arithmetic mean value of the upper and lower frequencies at the 40 dB filter attenuation level relative to the insertion loss ae. The temperature coefficient of frequency Tcf is valid both for the reference frequency fc and the frequency response of the filter in the operating temperature range. The frequency shift of the filter in the operating temperature range is not included in the production tolerance scheme.

Reference frequency fc at ambient temperature (fCAT) Pass band ) : Bandwidth at ambient temperature: dB - band width dB - band width dB - band width dB - band width dB - band width dB - band width

Amplitude ripple in pass band (p-p) : Relative attenuation fc MHz MHz............. fc arel MHz

Average group delay PB : Group delay ripple in PB (p-p) : Deviation from linear phase PB : Triple transit attenuation compared to main signal Crosstalk Temperature coefficient of frequency ( Tcf ) Frequency deviation of fc over temperature Operating temperature range Storage temperature range

fc(Hz) = Tcf(ppm/K) (T - TA) x fCAT (MHz) - 25 °C... - 25 °C... 85 °C

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road 14 513 TELTOW / Germany Hudson, 03051 / USA Tel: Fax: 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

3. Package 35 Max Pin 23 Pin 24 Pin 11 Pin 12 Pin 4-9, 16-21 Pin Input RF Return Output RF Return Ground not connected

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road 14 513 TELTOW / Germany Hudson, 03051 / USA Tel: Fax: 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

Name: Temperature: Time: pre-heating periods °C 60 sec. - 90 sec. main-heating periods over °C 20 sec. - 25 sec. peak temperature 5 °C

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road 14 513 TELTOW / Germany Hudson, 03051 / USA Tel: Fax: 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.


 

Some Part number from the same manufacture Vectron International
TFS70U Application = Wireless Communication ;; Center Frequency = 70.0 MHZ ;; 3 DB = 13.0 MHZ ;; Pass Band Ripple = 1.0dB  ;; Insertion Loss = 22.0dB ;; Group Delay Ripple = 30ns ;; Package = 13 MM X 6 MM LCC
TFS70V Application = Bandselective Repeater, Cellular ;; Center Frequency = 70.0 MHZ ;; 3 DB =  3.5 MHZ ;; Pass Band Ripple = 1.0dB ;; Insertion Loss = 27.0dB ;; Group Delay Ripple = 100ns ;; Package = 22 MM X 13 MM Dip
TFS71C Application = Wireless Communication ;; Center Frequency = 71.0 MHZ ;; 3 DB = 130 KHZ * ;; Pass Band Ripple =   ;; Insertion Loss = 7.6dB ;; Group Delay Ripple = 300ns ;; Package = 21 MM X 13 MM Dip
TFS71D
TFS75 Application = Wireless Communication ;; Center Frequency = 75.3 MHZ ;; 3 DB = 6.0 MHZ ;; Pass Band Ripple = 1.0dB ;; Insertion Loss = 26.0dB ;; Group Delay Ripple = 200ns ;; Package = 38 MM X 25 MM Dip
TFS80A Application = Mobile Communication Systems ;; Center Frequency = 80.0 MHZ ;; 3 DB = 200 KHZ ;; Pass Band Ripple =   ;; Insertion Loss = 16.5dB ;; Group Delay Ripple = 600ns ;; Package = 35 MM X 12 MM Dip
TFS80B
TFS80D Application = Wireless Communication ;; Center Frequency = 80.07 MHZ ;; 3 DB = 180 KHZ ;; Pass Band Ripple =   ;; Insertion Loss = 16.0dB ;; Group Delay Ripple = 600ns ;; Package = 38 MM X 25 MM Dip
TFS80D-1 Application = Mobile Communication Systems ;; Center Frequency = 80.07 MHZ ;; 3 DB = 180 KHZ ;; Pass Band Ripple =   ;; Insertion Loss = 16.0dB ;; Group Delay Ripple = 700ns ;; Package = 38 MM X 25 MM Dip
TFS80D-2
TFS80F Application = Wireless Communication ;; Center Frequency = 80.00 MHZ ;; 3 DB = 8.7 MHZ ;; Pass Band Ripple =   ;; Insertion Loss = 24.0dB ;; Group Delay Ripple = 150ns ;; Package = 13 MM X 6 MM LCC
TFS82A Application = Gsm,dcs,pcs ;; Center Frequency = 82.8 MHZ ;; 3 DB = 24 KHZ ;; Pass Band Ripple =   ;; Insertion Loss = 4.0dB ;; Group Delay Ripple = 10µs ;; Package = 13 MM X 6 MM LCC
TFS82B Application = Bandselective Repeater, Cellular ;; Center Frequency = 82.0 MHZ ;; 3 DB = 7.2 MHZ ;; Pass Band Ripple =   ;; Insertion Loss = 31.0dB ;; Group Delay Ripple =   ;; Package = 35 MM X 12 MM Dip
TFS86 Application = Amps ;; Center Frequency = 86.85 MHZ ;; 3 DB = 30 KHZ ;; Pass Band Ripple = 1.5dB ;; Insertion Loss = 4.0dB ;; Group Delay Ripple = 10µs ;; Package = 13 MM X 6 MM LCC
TFS86A
TFS86A-1
TFS87 Application = Base Station ;; Center Frequency = 87.1 MHZ ;; 3 DB = 2.4 MHZ ;; Pass Band Ripple = 1.0dB ;; Insertion Loss = 25.0dB ;; Group Delay Ripple = 150ns ;; Package = 35 MM X 20 MM Dip
TM-055 Frequency Range = 1.544 MHZ - 777.6 MHZ ;; Output = TTL / Pecl ;; Package (mm) = 50.8 X 50.8 X 14.86 ;; Features = DDS Based
TO-300 Frequency Range = 1.0MHz - 40MHz ;; Output Logic = LV - Hcmos Siave ;; Package = 4 Pin Dip ;; Features = Voltage Tune, Hermetic Seal, +3.3 Vdc, High Stability
TRU-050 Frequency Range = 1MHz - 65MHz ;; Output = TTL / CMOS ;; Package (mm) = 20.3 X 7.9 ;; Features = Loop Filter Software Loss of Signal Alarm

CD-700-KAF-HFB : Frequency Range = 12.0MHz - 65.536MHz ;; Output = CMOS ;; Package (mm) = 5.0 X 7.5 X 2 ;; Features = Complete Vcxo Based Phase Lock Loop

VC-400-GFD-305J : Frequency Range = 10MHz - 170MHz ;; Output = Ecl / Pecl ;; Package (mm) = Single Dip, Gull Wing or True Surface Mount FR4 ;; Features = 155.52 MHZ Prototypes Available in 2 Weeks

VTA2-4D0 :

VTC4-C12B-12M800 : Voltage Controlled Temperature Compensated Crystal Oscillator

VTC2J0AC-10M000 : Voltage Controlled Temperature Compensated Crystal Oscillator

CO-764PSB38316.384 : Surface Mount Oven Controlled Crystal Oscillators

FX-104-CFC-D4E9 : Frequency Translator

FX-104-CFF-A326 : Frequency Translator

FX-104-DFC-D1N7 : Frequency Translator

CS-300-CFC-C4D2M2G : Clock Smoother

FX-428-DFF-C4P9C : Low Jitter Frequency Translator

Same catergory

82C85 : CPU/Memory Specific PLL. CMOS Static Clock Controller/generator. The Intersil 82C85 Static CMOS Clock Controller/Generator provides complete control of static CMOS system operating modes and supports full speed, slow, stop-clock and stop-oscillator operation. While directly compatible with the Intersil 80C86 and 80C88 16-bit Static CMOS Microprocessor Family, the 82C85 can also be used for general system clock control.

8530DY-01 : . 16 differential 3.3V LVPECL outputs CLK, nCLK input pair CLK, nCLK pair can accept the following differential input levels: LVDS, LVPECL, LVHSTL, SSTL, HCSL Maximum output frequency: 500MHz Translates any single-ended input signal to 3.3V LVPECL levels with a resistor bias on nCLK input Output skew: 75ps (maximum) Part-to-part skew: 250ps (maximum).

CY2280 : 100-MHz Pentium ii Clock Synthesizer/driver With Spread Spectrum For Mobile or Desktop PCS.

CY2DP314OI : Backplane Interface. High Performance Clock Distribution Device. Four ECL/PECL differential outputs Two ECL/PECL and HSTL differential inputs Hot-swappable/-insertable 50 ps output-to-output skew (typical) 100ps device-to-device skew (typical) Less than 1-ps RMS typical jitter 500ps propagation delay (typical) Operation to 1.5 GHz, reduced swing to 3 GHz PECL and HSTL mode supply range: VCC to 3.465V with VEE = 0V ECL mode.

ICS8516 : General Purpose/. Low Skew 1-to-16 LVDS Clock Distribution Chip. 16 Differential LVDS outputs CLK, nCLK pair can accept the following differential input levels: LVPECL, LVDS, LVHSTL, HCSL, SSTL Maximum output frequency: 700MHz Translates any differential input signal (LVPECL, LVHSTL, SSTL, DCM) to LVDS levels without external bias networks Translates any single-ended input signal to LVDS with resistor bias on nCLK.

ICS9169A-70 : Application Specific PLL. Frequency Generator For Workstation Systems.

MC100H642FNR2 : Divider. Ecl/ttl Clock Driver, Package: Plcc, Pins=28. The MC10H/100H642 generates the necessary clocks for the 68030, 68040 and similar microprocessors. It is guaranteed to meet the clock s required by the 68030 and 68040 in terms of part­to­part skew, within­part skew and also duty cycle skew. The user has a choice of using either TTL or PECL (ECL referenced to +5.0V) for the input clock. TTL clocks are typically.

MLS9037-00110 : Frequency Synthesizers.  Surface Mount Frequency Synthesizer. Integrated VCO/PLL Miniature SMT Package Low Phase Noise +5V Operation The MLS9037-00110 synthesizer design integrates a high performance buffered VCO, PLL circuit and discrete loop filter in a surface mount package. The SMT packaging provides electrical shielding, easy PCB assembly and repeatable performance. The synthesizer is designed for use in CDMA.

MQF70.0-2000/01 : Monolithic Crystal Filter (MCF). Pole No. = 2 ;; Loss /dB =   ;; Passband /dB = 3.0 ;; Passband /±kHz = 10.00 ;; Ripple /dB = 1.0 ;; Ripple /±kHz = 6.0 ;; Stopband /dB = 15 ;; Stopband /±kHz = 30.00 ;; Stopband /dB =   ;; Stopband /±kHz =   ;; Impedance R/ohm = 2500 ;; Impedance C/pf = -1.50 ;; Remarks =  .

MQF9.0-0240/07 : Monolithic Crystal Filter (MCF). Pole No. = 8 ;; Loss /dB = 5.5 ;; Passband /dB = 6.0 ;; Passband /±kHz = 1.20 ;; Ripple /dB = 2.0 ;; Ripple /±kHz = 1.0 ;; Stopband /dB = 60 ;; Stopband /±kHz = 2.50 ;; Stopband /dB = 80 ;; Stopband /±kHz = 3.20 ;; Impedance R/ohm = 500 ;; Impedance C/pf = 30.00 ;; Remarks =   ;; Case.

MXO5164 : Package = 14 Dip ;; Frequency = 10 - 20 MHZ ;; Output Logic = Hcmos ;; Supply Voltage = +3.3 VDC ;; App Notes = -.

PLL250-647 : High Performance Signal Source. Model: PLL250-647 Rev: B Date: 6/4/2003 Customer: VARI-L COMPANY Operating Temperature Range: AppNote: 113 Option ° C) Parameter Frequency Range Step Size Settling Time - to within 5 deg. Output Power: RF Switch ON RF Switch OFF Output Phase Noise: 1 kHz 100 kHz 200 kHz 400 kHz 800 kHz 3000 kHz Power Supply: VCC 1: VCO, PLL CP VCC 2: Amp VCC 3: PLL IC,Switch.

PLL400-938 : High Performance Signal Source. Model: PLL400-938 Rev: A Date: 4/17/2003 Customer: VARI-L COMPANY Operating Temperature Range: AppNote: ° C) Parameter Frequency Range Step Size Settling Time - To within 1.0 kHz Output Power Output Phase Noise - 10 kHz Power Supply Current Spurious Product - 30 kHz Reference Feedthrough Harmonic Suppression: 2nd Harmonic 3rd Harmonic Ref Osc Signal:.

RFV300 : 3.3V 7.5 X 5mm Lv-pecl Rf-vcxo Ceramic SMD With Comp. Output. 3.3V Operation High Performance Complementary Output Pb Free Frequency Range (FO) Absolute Pull Range (APR) Vc=1.65V±1.5V Temperature Range Operating (TOPR) Storage (TSTG) Input Voltage (VDD) Control Voltage (VC) Input Current (IDD) Rise Time ~ 80% Vp-p) Fall Time ~ 20% Vp-p) Symmetry (50% Vp-p) Output Voltage (VOL) (VOH) Linearity Modulation Bandwidth.

TB31214FN : Dual or Single = Dual ;; = Integer - N (including Mixer) ;; Power Supply V = 2.0 ~ 5.5 ;; Ima = 16 ;; Input FMHZ = 200 ~ 400 ;; Operating Freq-mhz = 5 ~ 25 ;; Sensitivity DBµmV = 93 ~ 107 ;; Package = SSOP24 ;; Production Status = MP.

VCO190-492T : High Performance Signal Source. Model: VCO190-492T Rev: A Date: 4/22/2003 Customer: VARI-L COMPANY Operating Temperature Range: ° C) Parameter Frequency Range Tuning Voltage: 466 MHz 517 MHz Tuning Sensitivity Output Power Output Phase Noise: 10 kHz 100 kHz Power Supply Current Harmonic Suppression: 2nd Harmonic 3rd Harmonic Spurious (Non-Harmonic) Frequency Pushing 7.75-8.25 V Frequency.

TRF3761-C : TRF3761 is a family of high performance, highly integrated frequency synthesizers, optimized for high performance applications. The TRF3761 includes a low-noise, voltage-controlled oscillator (VCO) and an integer-N PLL. TRF3761 integrates divide-by 1, 2, or 4 options for a more flexible output frequency range. It is controlled through a 3-wire serial-programming-interface.

NB3N65027 : 3.3 V Programmable 3-PLL Clock Synthesizer With 6 LVTTL/LVCMOS Outputs W/OE The NB3N65027 is a pure CMOS high performance PLL synthesized clock generator. It accepts a 10 MHz to 27 MHz clock or fundamental mode crystal as the reference source for its integrated oscillator and drives three independent, low noise phase locked loops (PLLs)..

 
0-C     D-L     M-R     S-Z