Details, datasheet, quote on part number: M95040-WMN3T/W
PartM95040-WMN3T/W
Category
Description4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
CompanyST Microelectronics, Inc.
DatasheetDownload M95040-WMN3T/W datasheet
Quote
Find where to buy
 
  

 

Features, Applications
4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
FEATURES SUMMARY s Compatible with SPI Bus Serial Interface (Positive Clock SPI Modes)

5 MHz Clock Rate (maximum) Status Register BYTE and PAGE WRITE (up to 16 Bytes) Self-Timed Programming Cycle Adjustable Size Read-Only EEPROM Area Enhanced ESD Protection More than 1,000,000 Erase/Write Cycles More than 40 Year Data Retention

SUMMARY DESCRIPTION The a 4 Kbit x 8) electrically erasable programmable memory (EEPROM), accessed by a high speed SPI-compatible bus. The other members of the family (M95020, M95010) are identical, though proportionally smaller (2 and 1 Kbit, respectively). Each device is accessed by a simple serial interface that is SPI-compatible. The bus signals are C, D and Q, as shown in Table 1 and Figure 2. The device is selected when Chip Select (S) is taken Low. Communications with the device can be interrupted using Hold (HOLD). WRITE instructions are disabled by Write Protect (W). Figure 2. Logic Diagram

Note: 1. See page 28 (onwards) for package dimensions, and how to identify pin-1.

D Q Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect Hold Supply Voltage Ground

SIGNAL DESCRIPTION VCC must be held within the specified range: VCC(min) to VCC(max). All of the input and output signals can be held High or Low (according to voltages of VIH, VOH, VIL or VOL, as specified in Tables to 16). These signals are described next. Serial Data Output (Q) This output signal is used to transfer data serially out of the device. Data bytes are shifted out on the falling edge of the Serial Clock (C). Serial Data Input (D) This input signal is used to transfer data serially into the device. Instructions, addresses, and input data bytes are shifted in on the rising edge of the Serial Clock (C). Serial Clock (C) This input signal provides the timing for the serial interface.

Chip Select (S) When this input signal is High, the device is deselected, and the Serial Data Output (Q) is high impedance. Hold (HOLD) This input signal is used to pause temporarily any serial communications with the device, without losing bits that have already been passed on the serial bus. Write Protect (W) This input signal is used to control whether the memory is write protected. When W is held Low, writes to the memory are disabled, but other operations remain enabled. No action on this signal, or on the Write Enable Latch (WEL) bit, can interrupt a Write cycle that has already started.


 

Related products with the same datasheet
M95010-MN3/W
M95010-MN3T/W
M95010-MN6
M95010-WBN6
M95010-WMN6
M95020-MN3
M95020-MN3/W
M95020-MN3T/W
M95020-MN6
M95020-WBN6
M95020-WMN6
M95040-0WMN6
Some Part number from the same manufacture ST Microelectronics, Inc.
M95040-WMN5T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95080 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN3T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN6 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN6T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-MN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-MN3/W
M95080-MN3T
M95080-MN5T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-MN6 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-RBN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-RBN5 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-RBN5T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-RMN5 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-RMN6T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-S 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-VBN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock

M295V100-T70XN6TR : 1 Mbit 128kb x8 or 64kb X16, Boot Block Single Supply Flash Memory

PSD4235G3V-A-20MI : Flash In-system-programmable Peripherals For 16-bit MCUs

QST608CH0 : Capacitive Touch Sensor Device 8 keys with Individual key State Outputs or I2C Interface

UPSD3315BV-40T6T : Flash Programmable System Device with 8032 Microcontroller Core

ST62P25BB6/CCC : 8-bit MCUs WITH A/D Converter, TWO Timers, Oscillator Safeguard & SAFE Reset

ST92250JDV9QB : 8/16-bit Single Voltage Flash MCU Family WITH RAM, E3 Tm(emulated Eeprom), CAN 2.0B AND J1850 BLPD

M24128-BWMB3TP : 256/128 Kbit Serial IC Bus Eeprom Without Chip Enable Lines

ST7FLITEUS2U6TR : 8-bit MCU with Single Voltage Flash Memory, ADC, Timers

LD1084D2T80TR : 12 V FIXED POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSSO3 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, D2PAK-3 ; Life Cycle Stage: ACTIVE ; Output Voltage: 11.76 to 12.24 volts ; IOUT: 5 amps ; VIN: 13.6 to 30 volts ; Dropout Voltage: 1.5 volts

 
0-C     D-L     M-R     S-Z