Details, datasheet, quote on part number: M95040-WBN6T
PartM95040-WBN6T
CategoryLogic => Bus Exchangers
Description4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
CompanyST Microelectronics, Inc.
DatasheetDownload M95040-WBN6T datasheet
  

 

Features, Applications
4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
FEATURES SUMMARY s Compatible with SPI Bus Serial Interface (Positive Clock SPI Modes)

5 MHz Clock Rate (maximum) Status Register BYTE and PAGE WRITE (up to 16 Bytes) Self-Timed Programming Cycle Adjustable Size Read-Only EEPROM Area Enhanced ESD Protection More than 1,000,000 Erase/Write Cycles More than 40 Year Data Retention

SUMMARY DESCRIPTION The a 4 Kbit x 8) electrically erasable programmable memory (EEPROM), accessed by a high speed SPI-compatible bus. The other members of the family (M95020, M95010) are identical, though proportionally smaller (2 and 1 Kbit, respectively). Each device is accessed by a simple serial interface that is SPI-compatible. The bus signals are C, D and Q, as shown in Table 1 and Figure 2. The device is selected when Chip Select (S) is taken Low. Communications with the device can be interrupted using Hold (HOLD). WRITE instructions are disabled by Write Protect (W). Figure 2. Logic Diagram

Note: 1. See page 28 (onwards) for package dimensions, and how to identify pin-1.

D Q Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect Hold Supply Voltage Ground

SIGNAL DESCRIPTION VCC must be held within the specified range: VCC(min) to VCC(max). All of the input and output signals can be held High or Low (according to voltages of VIH, VOH, VIL or VOL, as specified in Tables to 16). These signals are described next. Serial Data Output (Q) This output signal is used to transfer data serially out of the device. Data bytes are shifted out on the falling edge of the Serial Clock (C). Serial Data Input (D) This input signal is used to transfer data serially into the device. Instructions, addresses, and input data bytes are shifted in on the rising edge of the Serial Clock (C). Serial Clock (C) This input signal provides the timing for the serial interface.

Chip Select (S) When this input signal is High, the device is deselected, and the Serial Data Output (Q) is high impedance. Hold (HOLD) This input signal is used to pause temporarily any serial communications with the device, without losing bits that have already been passed on the serial bus. Write Protect (W) This input signal is used to control whether the memory is write protected. When W is held Low, writes to the memory are disabled, but other operations remain enabled. No action on this signal, or on the Write Enable Latch (WEL) bit, can interrupt a Write cycle that has already started.


 

Related products with the same datasheet
M95010-BN5T
M95010-BN6T
M95010-DW3T
M95010-DW5T
M95010-DW6T
M95010-MN3T
M95010-MN5T
M95010-MN6T
M95010-SBN3T
M95010-SBN5T
M95010-SBN6T
M95010-SDW3T
Some Part number from the same manufacture ST Microelectronics, Inc.
M95040-WDW3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3T/W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN5T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95080 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN3T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN6 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN6T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-MN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-MN3/W
M95080-MN3T
M95080-MN5T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-MN6 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-RBN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-RBN5 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-RBN5T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock

HCF4017B : HCF->CMOS 4000B Series Counters/dividers

L7815ACV : Precision 1A Regulators

ST25C04M5TR : 4 Kbit Serial I2c Bus EePROM With User-defined Block Write Protection

ST90T158 : ST9 Family 8/16-BIT Microcontroller (MCU) With 16 to 64K ROM, OTP or EPROM, 512 to 2K RAM - ST9 + Family

TSM1013 : Constant Votalge & Current Controller For Battery Chargers & Adaptors

NAND01GW4A2BZA1 : 256/512mb/1gb (x8/x16, 1.8/3v, 528 Byte Page) NAND Flash Memories + 256/512mb (x16/x32, 1.8v) Lpsdram, MCP

PSD813F2A-15MT : 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 Specifications: Device Type: PIA-GENERAL PURPOSE ; Supply Voltage: 3.3V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: PLASTIC, LCC-52 ; Pins: 52 ; Features: RoHS

ST72521BAR9T3 : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: MROM ; Supply Voltage: 3.8 to 5.5 volts ; I/O Ports: 48 ; Package Type: TQFP, Other, 10 X 10 MM, PLASTIC, TQFP-64 ; Operating Range: Commercial ; Pin Count: 64 ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Features: PWM

ST72P361K6T6XXX : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 8 MHz ; ROM Type: MROM ; Supply Voltage: 4.5 to 5.5 volts ; I/O Ports: 26 ; Package Type: LFQP, Other, 7 x 7 MM, ROHS COMPLIANT, LQFP-32 ; Operating Range: Industrial ; Pin Count: 32 ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Feature

ST7PL35MA/XXXXS : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: MROM ; Supply Voltage: 3 to 5.5 volts ; I/O Ports: 15 ; Package Type: SOP, Other, 0.300 INCH, ROHS COMPLIANT, PLASTIC, SOP-20 ; Operating Range: Industrial ; Pin Count: 20 ; Operating Temperature: -40 to 85 C (-40 to 185 F) ;

TS339ID/IDT : COMPARATOR Specifications: Device Type: Comparators

 
0-C     D-L     M-R     S-Z