Details, datasheet, quote on part number: M95040-SDW5T
PartM95040-SDW5T
CategoryLogic => Bus Exchangers
Description4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
CompanyST Microelectronics, Inc.
DatasheetDownload M95040-SDW5T datasheet
  

 

Features, Applications
4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
FEATURES SUMMARY s Compatible with SPI Bus Serial Interface (Positive Clock SPI Modes)

5 MHz Clock Rate (maximum) Status Register BYTE and PAGE WRITE (up to 16 Bytes) Self-Timed Programming Cycle Adjustable Size Read-Only EEPROM Area Enhanced ESD Protection More than 1,000,000 Erase/Write Cycles More than 40 Year Data Retention

SUMMARY DESCRIPTION The a 4 Kbit x 8) electrically erasable programmable memory (EEPROM), accessed by a high speed SPI-compatible bus. The other members of the family (M95020, M95010) are identical, though proportionally smaller (2 and 1 Kbit, respectively). Each device is accessed by a simple serial interface that is SPI-compatible. The bus signals are C, D and Q, as shown in Table 1 and Figure 2. The device is selected when Chip Select (S) is taken Low. Communications with the device can be interrupted using Hold (HOLD). WRITE instructions are disabled by Write Protect (W). Figure 2. Logic Diagram

Note: 1. See page 28 (onwards) for package dimensions, and how to identify pin-1.

D Q Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect Hold Supply Voltage Ground

SIGNAL DESCRIPTION VCC must be held within the specified range: VCC(min) to VCC(max). All of the input and output signals can be held High or Low (according to voltages of VIH, VOH, VIL or VOL, as specified in Tables to 16). These signals are described next. Serial Data Output (Q) This output signal is used to transfer data serially out of the device. Data bytes are shifted out on the falling edge of the Serial Clock (C). Serial Data Input (D) This input signal is used to transfer data serially into the device. Instructions, addresses, and input data bytes are shifted in on the rising edge of the Serial Clock (C). Serial Clock (C) This input signal provides the timing for the serial interface.

Chip Select (S) When this input signal is High, the device is deselected, and the Serial Data Output (Q) is high impedance. Hold (HOLD) This input signal is used to pause temporarily any serial communications with the device, without losing bits that have already been passed on the serial bus. Write Protect (W) This input signal is used to control whether the memory is write protected. When W is held Low, writes to the memory are disabled, but other operations remain enabled. No action on this signal, or on the Write Enable Latch (WEL) bit, can interrupt a Write cycle that has already started.


 

Related products with the same datasheet
M95010-BN5T
M95010-BN6T
M95010-DW3T
M95010-DW5T
M95010-DW6T
M95010-MN3T
M95010-MN5T
M95010-MN6T
M95010-SBN3T
M95010-SBN5T
M95010-SBN6T
M95010-SDW3T
Some Part number from the same manufacture ST Microelectronics, Inc.
M95040-SDW6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WBN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WBN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WBN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3T/W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN5T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95080 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN3T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN6 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN6T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-MN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-MN3/W
M95080-MN3T
M95080-MN5T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock

LF30C : Very Low Drop Voltage Regulators With Inhibit

M27C4001-70B6X : 4 Mbit 512kb X 8 uv EPROM And OTP EPROM

M28256-25-6 : 256 Kb 256K (32K X8) Parallel EePROM With Software Data Protection

M28C64-20MS6T : 64 Kbit 8k X 8 Parallel EePROM With Software Data Protection

M29W022BT90NZ1T : 2 Mbit 256kb X8, Boot Block Low Voltage Single Supply Flash Memory

PSD935G3V-B-15JI : Configurable Memory System on a Chip For 8-bit Microcontrollers

STGWA30N120KD : IGBT Specifications: Transistor Type / Technology: IGBT

74AUP1G09GN : AUP/ULP/V SERIES, 2-INPUT NAND GATE, PDSO6 Specifications: Gate Type: NAND ; Logic Family: CMOS ; Inputs: 2 ; Propagation Delay: 17.2 ns ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Pin Count: 6 ; IC Package Type: Other, 1.20 X 1 MM, ROHS COMPLIANT, DFN-6

 
0-C     D-L     M-R     S-Z