Details, datasheet, quote on part number: M95040-MN6
PartM95040-MN6
Category
Description4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
CompanyST Microelectronics, Inc.
DatasheetDownload M95040-MN6 datasheet
Cross ref.Similar parts: CAT25040VI-G, BR25H040FJ-2CE2, BR25L040FJ-WE2
Quote
Find where to buy
 
  

 

Features, Applications
4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
FEATURES SUMMARY s Compatible with SPI Bus Serial Interface (Positive Clock SPI Modes)

5 MHz Clock Rate (maximum) Status Register BYTE and PAGE WRITE (up to 16 Bytes) Self-Timed Programming Cycle Adjustable Size Read-Only EEPROM Area Enhanced ESD Protection More than 1,000,000 Erase/Write Cycles More than 40 Year Data Retention

SUMMARY DESCRIPTION The a 4 Kbit x 8) electrically erasable programmable memory (EEPROM), accessed by a high speed SPI-compatible bus. The other members of the family (M95020, M95010) are identical, though proportionally smaller (2 and 1 Kbit, respectively). Each device is accessed by a simple serial interface that is SPI-compatible. The bus signals are C, D and Q, as shown in Table 1 and Figure 2. The device is selected when Chip Select (S) is taken Low. Communications with the device can be interrupted using Hold (HOLD). WRITE instructions are disabled by Write Protect (W). Figure 2. Logic Diagram

Note: 1. See page 28 (onwards) for package dimensions, and how to identify pin-1.

D Q Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect Hold Supply Voltage Ground

SIGNAL DESCRIPTION VCC must be held within the specified range: VCC(min) to VCC(max). All of the input and output signals can be held High or Low (according to voltages of VIH, VOH, VIL or VOL, as specified in Tables to 16). These signals are described next. Serial Data Output (Q) This output signal is used to transfer data serially out of the device. Data bytes are shifted out on the falling edge of the Serial Clock (C). Serial Data Input (D) This input signal is used to transfer data serially into the device. Instructions, addresses, and input data bytes are shifted in on the rising edge of the Serial Clock (C). Serial Clock (C) This input signal provides the timing for the serial interface.

Chip Select (S) When this input signal is High, the device is deselected, and the Serial Data Output (Q) is high impedance. Hold (HOLD) This input signal is used to pause temporarily any serial communications with the device, without losing bits that have already been passed on the serial bus. Write Protect (W) This input signal is used to control whether the memory is write protected. When W is held Low, writes to the memory are disabled, but other operations remain enabled. No action on this signal, or on the Write Enable Latch (WEL) bit, can interrupt a Write cycle that has already started.


 

Related products with the same datasheet
M95010-MN3/W
M95010-MN3T/W
M95010-MN6
M95010-WBN6
M95010-WMN6
M95020-MN3
M95020-MN3/W
M95020-MN3T/W
M95020-MN6
M95020-WBN6
M95020-WMN6
M95040-0WMN6
Some Part number from the same manufacture ST Microelectronics, Inc.
M95040-MN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-R 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-SBN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WBN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WBN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WBN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN3T/W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN5T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-WMN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95080 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN1T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN3T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-BN6 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-BN6T 64/32/16/8 Kbit Serial Spi Bus EePROM With High Speed Clock
M95080-MN3 16KBIT And 8KBIT Serial Spi Bus EePROM With High Speed Clock
M95080-MN3/W

PSD311B-90JI : PSD3XX/ZPSD3XX Family Low Cost Microcontroller Peripherals

STM812TW16F : Reset Circuit

UPSD3212CV : 8-bit Microcontrollers Flash programmable system device with 8032 MCU with USB and programmable logic

M93C-56BN6TP : 16kbit, 8kbit, 4kbit, 2kbit and 1kbit (8-bit or 16-bit Wide) Microwire Serial Access Eeprom

M24C01-MN3TP : 16kbit, 8kbit, 4kbit, 2kbit and 1kbit Serial I2C Bus Eeprom

STB21NK50Z : Fet - Single Discrete Semiconductor Product 17A 500V 190W Surface Mount; MOSFET N-CH 500V 17A D2PAK Specifications: Mounting Type: Surface Mount ; FET Type: MOSFET N-Channel, Metal Oxide ; Drain to Source Voltage (Vdss): 500V ; Current - Continuous Drain (Id) @ 25 C: 17A ; Rds On (Max) @ Id, Vgs: 270 mOhm @ 8.5A, 10V ; Input Capacitance (Ciss) @ Vds: 2600pF @ 25V ; Power - Max: 190W ; Packaging:

ST1L02PM : ADJUSTABLE POSITIVE LDO REGULATOR, PDSO6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Adjustable / Variable ; Package Type: Other, 3 X 3 MM, LEAD FREE, DFN-6 ; Life Cycle Stage: ACTIVE

STM8AF5198TBX : MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Package Type: LFQP, Other, 10 X 10 MM, ROHS COMPLIANT, LQFP-64 ; Pin Count: 64

 
0-C     D-L     M-R     S-Z