Details, datasheet, quote on part number: M95010-WMN6T
PartM95010-WMN6T
CategoryLogic => Bus Exchangers
Description4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
CompanyST Microelectronics, Inc.
DatasheetDownload M95010-WMN6T datasheet
Quote
Find where to buy
 
  

 

Features, Applications
4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
FEATURES SUMMARY s Compatible with SPI Bus Serial Interface (Positive Clock SPI Modes)

5 MHz Clock Rate (maximum) Status Register BYTE and PAGE WRITE (up to 16 Bytes) Self-Timed Programming Cycle Adjustable Size Read-Only EEPROM Area Enhanced ESD Protection More than 1,000,000 Erase/Write Cycles More than 40 Year Data Retention

SUMMARY DESCRIPTION The a 4 Kbit x 8) electrically erasable programmable memory (EEPROM), accessed by a high speed SPI-compatible bus. The other members of the family (M95020, M95010) are identical, though proportionally smaller (2 and 1 Kbit, respectively). Each device is accessed by a simple serial interface that is SPI-compatible. The bus signals are C, D and Q, as shown in Table 1 and Figure 2. The device is selected when Chip Select (S) is taken Low. Communications with the device can be interrupted using Hold (HOLD). WRITE instructions are disabled by Write Protect (W). Figure 2. Logic Diagram

Note: 1. See page 28 (onwards) for package dimensions, and how to identify pin-1.

D Q Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect Hold Supply Voltage Ground

SIGNAL DESCRIPTION VCC must be held within the specified range: VCC(min) to VCC(max). All of the input and output signals can be held High or Low (according to voltages of VIH, VOH, VIL or VOL, as specified in Tables to 16). These signals are described next. Serial Data Output (Q) This output signal is used to transfer data serially out of the device. Data bytes are shifted out on the falling edge of the Serial Clock (C). Serial Data Input (D) This input signal is used to transfer data serially into the device. Instructions, addresses, and input data bytes are shifted in on the rising edge of the Serial Clock (C). Serial Clock (C) This input signal provides the timing for the serial interface.

Chip Select (S) When this input signal is High, the device is deselected, and the Serial Data Output (Q) is high impedance. Hold (HOLD) This input signal is used to pause temporarily any serial communications with the device, without losing bits that have already been passed on the serial bus. Write Protect (W) This input signal is used to control whether the memory is write protected. When W is held Low, writes to the memory are disabled, but other operations remain enabled. No action on this signal, or on the Write Enable Latch (WEL) bit, can interrupt a Write cycle that has already started.


 

Related products with the same datasheet
M95010-BN5T
M95010-BN6T
M95010-DW3T
M95010-DW5T
M95010-DW6T
M95010-MN3T
M95010-MN5T
M95010-MN6T
M95010-SBN3T
M95010-SBN5T
M95010-SBN6T
M95010-SDW3T
Some Part number from the same manufacture ST Microelectronics, Inc.
M95010BN 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-BN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-MN3 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-MN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-MN3T/W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-MN5T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-MN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-MN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-R 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-SBN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-W 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-WBN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-WBN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-WBN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95020-WMN6 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95020-WMN6T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock
M95040-0WMN6
M95040-BN3T 4kbit, 2kbit And 1kbit Serial Spi Bus EePROM With High Speed Clock
M95040-MN3 4KBIT, 2KBIT And 1KBIT Serial Spi Bus EePROM With High Speed Clock

TS4040EIZ-2.5 : 2.5V Micropower Shunt Voltage Reference

M28W640FSB : 32Mbit (2Mbx16, Boot Block) and 64Mbit (4Mbx16, Boot Block) 3V Supply Secure Flash Memories SUPPLY VOLTAGE VDD = 2.7V to 3.6V Core Power Supply VDDQ= 1.65V to 3.6V for Input/Output VPP = 12V for fast Program (optional) ACCESS TIME: 70ns PROGRAMMING TIME: 10s typical Double Word Programming Opti

M93C76-WMB3TP : 16kbit, 8kbit, 4kbit, 2kbit and 1kbit (8-bit or 16-bit Wide) Microwire Serial Access Eeprom

NAND512R3A2AV1E : 256/512mb/1gb (x8/x16, 1.8/3v, 528 Byte Page) NAND Flash Memories + 256/512mb (x16/x32, 1.8v) Lpsdram, MCP

M68AF127BL55MC1T : 1mbit 128K x8, 5V Asynchronous SRAM

L78L20ABD13TR : Positive Voltage Regulators

M95040-WMB6G : 512 X 8 SPI BUS SERIAL EEPROM, DSO8 Specifications: Density: 4 kbits ; Number of Words: 512 k ; Bits per Word: 8 bits ; Bus Type: Serial ; Production Status: Full Production ; Data Rate: 10 MHz ; Supply Voltage: 5V ; Package Type: 2 X 3 MM, ROHS COMPLIANT, MLP-8 ; Pins: 8 ; Operating Range: Industrial ; Operating Temperature: -40 to 8

PSD813F1AV-20MIT : 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 Specifications: Device Type: PIA-GENERAL PURPOSE ; Supply Voltage: 3.3V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: PLASTIC, LCC-52 ; Pins: 52 ; Features: RoHS

LDK130PU29R : LDO Voltage Regulators 300 mA low quiescent current very low noise LDO STMicroelectronics LDK130P DFN-6L Low Drop Voltage Regulators provide 300mA of maximum current from an input supply voltage in the range of 1.9V to 5.5V, with a typical dropout voltage of 100mV. It is stabilized with a ceramic capacitor on the output. The very low drop voltage, low quiescent curr

 
0-C     D-L     M-R     S-Z