|Category||Interface and Interconnect|
|Description||15kV ESD-Protected, Quad, Low-power RS-232 Line Driver|
|Company||Maxim Integrated Products|
|Datasheet||Download MAX1488E datasheet
|Cross ref.||Similar parts: MC1488, SN75188|
The MAX1488E quad, low-power line driver is designed for EIA/TIA-232, EIA/TIA-562, and CCITT V.28 communications in harsh environments. Each transmitter output is protected against ±15kV electrostatic discharge (ESD) shocks. The inputs are TTL and CMOS compatible with minimal loading. The outputs feature internally controlled slew-rate limiting and current limiting. This device has a guaranteed 120kbps data rate. Powersupply current is less than 180µA over to ±13.2V supply voltage range. The MAX1488E is pin compatible with the SN75C188, DS1488, and It is available in 14-pin plastic DIP and SO packages.
o ESD Protection: ±15kV--Human Body Model ±6kV--IEC801-2, Contact Discharge ±15kV--IEC801-2, Air-Gap Discharge o Latchup Free, Even During an ESD Event o Low 85µA Supply Current from IEE or ICC o Guaranteed 120kbps Data Rate o No External Capacitors Required for Slew-Rate Limiting o Pin Compatible with SN75C188, DS1488, and DS14C88
PC Motherboards Modems Interface Data Terminal Equipment (DTE) with Data Circuit-Terminating Equipment (DCE) Equipment Meeting IEC1000-4-2 (formerly or ±15kV ESD Protection
PART MAX1488EC/D MAX1488EEPD TEMP. RANGE to +85°C PIN-PACKAGE 14 Plastic DIP 14 SO Dice* 14 Plastic DIP 14 SOVEE 1 TTL/CMOS LOGIC INTERCONNECTING CABLE TTL/CMOS LOGIC INPUT A 2 OUTPUT A 3 INPUT B1 4
13 INPUT D1 12 INPUT D2 11 OUTPUT D 10 INPUT 9 8 INPUT C2 OUTPUT C
Call toll free 1-800-998-8800 for free samples or literature.
Positive Supply Voltage (VCC).............................................+14V Negative Supply Voltage (VEE).............................................-14V Input Voltage to +15V Driver Output Voltage..........................................................±15V Continuous Power Dissipation (TA = +70°C) Plastic DIP (derate 10.00mW/°C above +70°C)..........800mW SO (derate 8.7mW/°C above +70°C)...........................695mW Operating Temperature Ranges to +85°C Storage Temperature to +160°C Lead Temperature (soldering, 10sec).............................+300°C
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
(VCC to 13.2V, VEE TA = TMIN to TMAX, unless otherwise noted. Typical values are = +25°C.) PARAMETER DC CHARACTERISTICS VCC = -VEE = 3k VCC = -VEE = 3k VCC = -VEE = 3k VCC = -VEE RL = open VCC = -VEE = 3k VCC = -VEE = 3k VCC = -VEE = 3k VCC = -VEE RL = open No load No load Output shorted to ground (Note VCC = VEE = 0V IVOI 2.0V VCC = 4.5V, VEE = 50pF tPLH VCC = 9.0V, VEE = 50pF VCC = 12.0V, VEE = 50pF Output Propagation Delay, High to Low Propagation Delay Skew, VCC = 4.5V, VEE = 50pF tPHL VCC = 9.0V, VEE = 50pF VCC = 12.0V, VEE = 50pF VCC = 4.5V, VEE = 50pF tSK VCC = 9.0V, VEE = 50pF VCC = 12.0V, VEE = 50pF Human Body Model ESD Protection IEC-1000-4-2 (Contact Discharge) IEC-1000-4-2 (Air-Gap Discharge) kV µs SYMBOL CONDITIONS MIN TYP MAX UNITS
Operating Voltage Range Positive Supply Current Negative Supply Current Output Short-Circuit Current Input High Voltage Input Low Voltage Input Current Output ResistanceTIMING CHARACTERISTICS (see Figure 1) Output Propagation Delay, Low to High
(VCC to 13.2V, VEE TA = TMIN to TMAX, unless otherwise noted. Typical values are = +25°C.) PARAMETER SYMBOL tR1 Output Rise Time tR2 tF1 Output Fall Time tF2 CONDITIONS = 5k, VOUTPUT_ from = 5k, VOUTPUT_ from = 5k, VOUTPUT_ from = 5k, VOUTPUT_ from to 7k, VCC = 12V, VEE = +25°C, VOUTPUT_ from to 7k, VCC = 12V, VEE +25°C 4 MIN TYP ns 765 MAX UNITS
Note 1: The IOS value is for one output at a time. If more than one output is shorted simultaneously, damage may occur.
|Related products with the same datasheet|
|Some Part number from the same manufacture Maxim Integrated Products|
|MAX1488EC 15kV ESD-Protected, Quad, Low-power RS-232 Line Driver|
|MAX1489E 15kV ESD-Protected, Quad, Low-power RS-232 Line Receiver|
|MAX148A +2.7V to +5.25V Low-power 8-Channel Serial 10-Bit ADCs|
|MAX1490A Complete, ISOlated RS-485/RS-422 Data Interface|
|MAX1490E 15kV ESD-Protected, ISOlated RS-485/RS-422 Data Interfaces|
|MAX1491 MAX1491, MAX1492, MAX1493, MAX1494 Preliminary Product Information: Sigma Delta ADC With LCD Display Drivers|
|MAX1491CAI 3.5- And 4.5-digit, Single-chip ADCs With LCD Drivers|
|MAX1492 MAX1491, MAX1492, MAX1493, MAX1494 Preliminary Product Information: Sigma Delta ADC With LCD Display Drivers|
|MAX1493CCJ 3.5- And 4.5-digit, Single-chip ADCs With LCD Drivers|
|MAX1494 MAX1491, MAX1492, MAX1493, MAX1494 Preliminary Product Information: Sigma Delta ADC With LCD Display Drivers|
|MAX1495 3.5- And 4.5-Digit, Single-chip ADCs With LCD Drivers|
|MAX1495CCJ 3.5- And 4.5-digit, Single-chip ADCs With LCD Drivers|
|MAX1496 3.5- And 4.5-Digit, Single-chip ADCs With Led Drivers|
|MAX1497 3.5- And 4.5-Digit, Single-chip ADCs With Led Drivers And µC Interface<<<>>>low-power, 3.5- And 4.5-digit, Analog-to-digital Converters (ADCs) With Integrated Lightemitting Diode (LED) Drivers Operate|
|MAX1498 3.5- And 4.5-Digit, Single-chip ADCs With Led Drivers|
|MAX1499 3.5- And 4.5-Digit, Single-chip ADCs With Led Drivers And µC Interface<<<>>>low-power, 3.5- And 4.5-digit, Analog-to-digital Converters (ADCs) With Integrated Lightemitting Diode (LED) Drivers Operate|
|MAX149A +2.7V to +5.25V Low-power 8-Channel Serial 10-Bit ADCs|
|MAX150 CMOS, 1.3 s, 8-Bit ADC With Voltage Reference And Track/hold|
|MAX1501 MAX1501 Highly Integrated, Linear Battery Charger With Thermal Regulation For Portable Applications|
|MAX1501EVKIT MAX1501EVKIT Evaluation Kit For The MAX1501|
|MAX1507 MAX1507 Linear Li+ Battery Charger With Integrated Pass Fet And Thermal Regulation in a 3mm X 3mm Thin DFN|
DG403AZ : Improved, Dual, High-speed Analog Switches
MAX1647 : Power Chemistry-independent Battery Chargers
MAX6321HPUK40DX-T : Watchdog 5-Pin P Supervisory Circuits With Watchdog And Manual Reset
MAX264ACWI-T : Pin-Programmable Universal And Bandpass Filters The MAX263/264 and MAX267/268 CMOS switched-capacitor active filters are designed for precision filtering applications. Center frequency, Q, and operating mode are all selected via pin-strapped inputs. The MAX263/264 uses no external components for a
MAX6382XS41D5-T : Sc70, Single/dual Low-voltage, Low-power ¥ìP Reset Circuits
MAX6385XS30D3-T : Sc70, Single/dual Low-voltage, Low-power ¥ìP Reset Circuits
LM4040CEM3-3.0-T : Improved Precision Micropower Shunt Voltage Reference With Multiple Reverse Breakdown Voltages The LM4040 is a precision two-terminal shunt mode, bandgap voltage reference available in fixed reverse breakdown voltages of 2.048V, 2.500V, 3.000V, 3.3V, 4.096V, and 5.000V. Ideal for space-critical app
MAX6865UK21D1S+T : Pmic - Supervisor Integrated Circuit (ics) Simple Reset/Power-On Reset Tape & Reel (TR) 1; IC MPU SUPERVISOR SOT23-5 Specifications: Output: Push-Pull, Totem Pole ; Reset: Active High ; Package / Case: SC-74A, SOT-753 ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: 1 ; Reset Timeout: 10 ms Minimum ; Type: Simple Reset/Power-On Reset ; Voltage - Threshold: 2.1V ; Operating Temperature: -40°C ~ 85°
MAX203EWP+TG36 : Interface - Drivers, Receivers, Transceiver Integrated Circuit (ics) Transceiver Tape & Reel (TR) 4.75 V ~ 5.25 V; IC TXRX RS-232 W/CAP 20-SOIC Specifications: Number of Drivers/Receivers: 2/2 ; Type: Transceiver ; Voltage - Supply: 4.75 V ~ 5.25 V ; Package / Case: 20-SOIC (0.295", 7.50mm Width) ; Packaging: Tape & Reel (TR) ; Protocol: RS232 ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant
DG201ACSE-T : QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDIP16 Specifications: Supply Voltage (VS): -15 to 18 volts ; Ron: 200 ohms ; tON: 600 ns ; tOFF: 450 ns ; Operating Temperature: 0.0 to 70 C (32 to 158 F) ; Logic Family: CMOS ; Package Type: DIP, 0.300 INCH, PLASTIC, MO-058AB, MS-001AA, DIP-16 ; Number of Pins: 16 ; Number of Devices: 4
MAX8530ETT8A : DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PBGA6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, 1.16 X 1.57 MM, 0.60 MM HEIGHT, UCSP-6 ; Life Cycle Stage: ACTIVE ; Output Voltage: 2.72 to 2.88 volts ; IOUT: 0.2000 amps ; VIN: 2.5 to 6.5 volts ; Dropout Voltage: 0.2000 vol
5962-7802004M2A : Non-Standard Line Circuits. ti AM26LS33A, Quadruple Differential Line Receiver.
A8932 : . RET REF V FLT V BEMF GROUND UV SET R OUT P OUT SWITCH IN N OUT SW RETRACT FAULT MP RESET SIGNAL SUPPLY RET SET V SENS V LOAD Providing control and drive of the voice-coil motor used for head positioning 5 V disk drive applications, the second-generation is a full-bridge driver that can be configured so that its output current is a direct function of an externally.
CDP1851 : CMOS Programmable I/o Interface. THE CDP1851 and CDP1851C are CMOS programmable twoport I/Os designed for use as general-purpose I/O devices. They are directly compatible with CDP1800-series microprocessors functioning at maximum clock frequency. Each port can be programmed in either byte-I/O or bit-programmable modes for interfacing with peripheral devices such as printers and keyboards.
EL1504C : 15V Cpe Driver. Complete ADSL differential driver 45VP-P differential output drive into 200 -60dBc typical output distortion at full output at 2MHz Drives 8 single-ended video loads, or 4 S-VHS loads, or 4 differential video loads Power surface-mount package The EL1504/5C contains two wideband high-voltage drivers. It is designed to drive 45VP-P signals at 2MHz into.
FDC37N769 : 3.3v Super I/o Controller With Infrared Support For Portable Applications.
GreenCoderUR5HCFJL : . GreenCoderTM UR5HCFJL Extremely Low-Power Keyboard Encoder for Portable Systems HID & SYSTEM MANAGEMENT PRODUCTS, KEYCODERTM FAMILY The GreenCoderTM is a unique, extremely low-power keyboard encoder that performs optimally in both battery-operated and desktop systems. The GreenCoderTM scans, debounces, and encodes X 16* keyboard matrix, and provides.
HT82K628A : Windows 2000 Keyboard Encoder. Design for Windows 95/98/2000/NT Supports WindowsTM keys Supports PC/AT and PS/2 code set 2, 3 Supports Japanese , Korean , Brazilian and 101/102/104/105/107/109 keys or other special ap- The is a keyboard encoder designed for IBM PC/AT, IBM PS/2 and all compatible machines. The HT82K628A accepts keyboard inputs and provides a 16-character first-in-first-out.
MC1488 : Rs-232 Quad Line Driver (sn75188n): 4 Drivers. Meet or Exceed the Requirements of ANSI EIA/ TIA-232-E and ITU Recommendation V.28 Designed to Be Interchangeable With Motorola MC1488 Current-Limited Output: 10 mA Typical Power-Off Output Impedance: 300 Minimum Slew Rate Control by Load Capacitor Flexible Supply Voltage Range Input Compatible With Most TTL Circuits The MC1488, SN55188, and SN75188.
MCP2551 : High-speed CAN Transceiver, Industry-standard Pinout, ISO-118980 Compatible.
PC87363 : 128-pin LPC Superi/o With Midi And Game Ports, Extended Wake-up And Protection.
PCF1171C : PCF1171C; 4-digit LCD Car Clock. Product Supersedes data of September 1993 File under Integrated Circuits, IC16 1997 Apr 16 Internal voltage regulator for 5 V LCD Option for external stabilized voltage supply 4.19 MHz oscillator Integrated oscillator output capacitor and polarization resistor Operating ambient temperature: to +85 °C 40-lead plastic SMD, face down (VSO40). ORDERING.
SCANSTA112 : SCANSTA112 - 7-port Multidrop Ieee 1149.1 (JTAG) Multiplexer, Package: Fbga, Pin Nb=100.
SN65LBC031 : . SN65LBC031Q, SN75LBC031 HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS SN75LBC031 Meets Standard ISO/DIS 11898 (up 500 k Baud) Driver Output Capability 50 mA Wide Positive and Negative Input/output Bus Voltage Range Bus Outputs Short-Circuit-Protected to Battery Voltage and Ground Thermal Shutdown Available in Q-Temp Automotive HighRel Automotive.
SN65LVDS047 : LVDS Quad Differential Line Driver. D >400 Mbps (200 MHz) Signaling Rates D Flow-Through Pinout Simplifies PCB Layout 300 ps Maximum Differential Skew Propagation Delay Times 1.8 ns (Typical) 3.3 V Power Supply Design ±350 mV Differential Signaling High Impedance on LVDS Outputs on Power Down Conforms to TIA/EIA-644 LVDS Standard Industrial Operating Temperature Range to 85°C) Available.
SN75976A : 9-channel Differential Transceiver. Improved Speed and Package Replacement for the SN75LBC976 Designed to Operate to 20 Million Data Transfers per Second (Fast-20 SCSI) Nine Differential Channels for the Data and Control Paths of the Small Computer Systems Interface (SCSI) and Intelligent Peripheral Interface (IPI) SN75976A Packaged in Shrink Small-Outline Package with 25-Mil Terminal.
SN75C23243 : . Single-Chip and Single-Supply Interface for Two IBM PC/AT Serial Ports Meet or Exceed the Requirements of TIA/EIA-232-F and ITU v.28 Standards Operate With to 5.5-V VCC Supply Always-Active Noninverting Receiver Output (ROUT2) Per Port Operate to 250 kbit/s Low Standby Current. 1 µA Typical External Capacitors. 0.22 µF Accept 5-V Logic Input With 3.3-V.
UC3710 : High Current Fet Driver. Totem Pole Output with 6A Source/Sink Drive 3ns Delay 20ns Rise and Fall Time into 2.2nF 8ns Rise and Fall Time into to 18V Operation Inverting and Non-Inverting Outputs Under-Voltage Lockout with Hysteresis Thermal Shutdown Protection MINIDIP and Power Packages The UC1710 family of FET drivers is made with a high-speed Schottky process to interface.
TCA6507 : Low-Voltage 7-Bit I2C And SMBus LED Driver With Intensity Control And Shutdown This 7-bit LED dimmer for the two-line bidirectional bus (I2C) is designed to control (or dim) LEDs via the I2C interface [serial clock (SCL), serial data (SDA)]. Without this device, the microprocessor or microcontroller must be actively involved in turning on and off the LEDs.
ADM2582E : Signal And Power Isolated RS-485 Transceiver With ±15 KV ESD Protection The ADM2582E/ADM2587E are fully integrated signal and power isolated data transceivers with ±15 kV ESD protection and are suitable for high speed communication on multipoint transmission lines. The ADM2582E/ADM2587E include an integrated isolated dc-to-dc power supply, which eliminates.
NCN8025 : The NCV7340 CAN Transceiver Is The Interface Between A Controller Area Network (CAN) Protocol Controller And The Physical Bus And May Be Used In Both 12 V And 24 V Systems. The Transceiver Provides Differential Transmit Capability To The Bus And Differential Receive Capability To The CAN Controller. The NCV7340 Is A New Addition To The CAN High-speed.