Details, datasheet, quote on part number: MAX1457CWI
PartMAX1457CWI
CategorySensors => Sensor Signal Conditioners
Description0.1% Accurate Signal Conditioner For Piezoresistive Sensor Compensation
CompanyMaxim Integrated Products
DatasheetDownload MAX1457CWI datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The is a highly integrated analog-sensor signal processor optimized for piezoresistive sensor calibration and compensation. It includes a programmable current source for sensor excitation, a 3-bit programmable-gain amplifier (PGA), a 12-bit ADC, five 16-bit DACs, and an uncommitted op amp. Achieving a total error factor within 0.1% of the sensor's repeatability errors, the MAX1457 compensates offset, full-span output (FSO), offset TC, FSO TC, and full-span output nonlinearity of silicon piezoresistive sensors. The MAX1457 calibrates and compensates first-order temperature errors by adjusting the offset and span of the input signal via digital-to-analog converters (DACs), thereby eliminating quantization noise. If needed, residual higher-order errors are then compensated using linear interpolation of the first-order coefficients stored in a look-up table (in external EEPROM). The MAX1457 integrates three traditional sensormanufacturing operations into one automated process: Pretest: Data acquisition of sensor performance under the control of a host test computer. Calibration and Compensation: Computation and storage (in an external EEPROM) of calibration and compensation coefficients determined from transducer pretest data. Final Test: Verification of transducer calibration and compensation, without removal from a pretest socket. Analog outputs are provided for both pressure and temperature. A general-purpose, uncommitted op amp is also included on-chip to increase the overall circuit gain, or to facilitate the implementation 2-wire, 420mA transmitter. The serial interface is compatible with MicroWireTM and SPITM, and directly connects to an external EEPROM. Additionally, built-in testability features of the MAX1457 facilitate manufacturing and calibration of multiple sensor modules, thus lowering manufacturing cost. Although optimized for use with piezoresistive sensors, the MAX1457 may also be used with other resistive sensor types (i.e., accelerometers and strain gauges) with the addition of a few external components.

o High Accuracy (within 0.1% of sensor's repeatable errors) o Compensates Offset, Offset TC, FSO, FSO TC, Temperature/Pressure Nonlinearity o Rail-to-Rail Analog Output for Calibrated, Temperature-Compensated Pressure Measurements o Programmable Sensor Excitation Current o SPI/MicroWire-Compatible Serial Interface o Fast Signal-Path Settling Time (<1ms) o Accepts Sensor Outputs from 30mV/V o Pin-Compatible with MCA7707

PART TEMP. RANGE PIN-PACKAGE +70C 28 Wide +70C 32 TQFP to +70C Dice* Ordering Information continued at end of data sheet. Note: Contact the factory for customized solutions. *Dice are tested = +25C.

VDD BIAS GENERATOR NBIAS FADJ FOUT VOUT LINDAC FSOTCDAC OTCDAC OFSTDAC FSODAC A=1 LINOUT A=1 FSOTCOUT VBDRIVE A=1 VBBUF

Maxim can customize the MAX1457 for unique requirements. With a dedicated cell library of more than 90 sensor-specific functional blocks, Maxim can quickly provide customized MAX1457 solutions. Contact Maxim for additional information.

Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. SPI is a trademark of Motorola, Inc. MicroWire is a trademark of National Semiconductor Corp.

MCS ECS ECLK EDI EDO LINDACREF AMP+ AMPSERIAL EEPROM INTERFACE

For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468.

Supply Voltage, VDD to +6V All other pins....................................(VSS 0.3V) to (VDD + 0.3V) Continuous Power Dissipation (TA +70C) 28-Pin Wide SO (derate 12.50mW/C above +70C)..........1W 32-Pin TQFP (derate 11.1mW/C above +70C)...........889mW Operating Temperature Ranges to +125C Storage Temperature to +150C Lead Temperature (soldering, 10sec).............................+300C

Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

(VDD = +5V, VSS = +25C, unless otherwise noted.) PARAMETER GENERAL CHARACTERISTICS Supply Voltage Supply Current ANALOG INPUT (PGA) Input Impedance Input-Referred Offset Tempco Amplifier Gain Nonlinearity Output Step-Response Time Common-Mode Rejection Ratio Input-Referred Adjustable Offset Range Input-Referred Adjustable Full-Span Output Range ANALOG OUTPUT (PGA) Differential Signal Gain Range Minimum Differential Signal Gain Differential Signal Gain Tempco Output Voltage Swing Output Current Range Output Noise CURRENT SOURCE Bridge Current Range Bridge Voltage Swing Current-Source Reference Input Voltage Range DAC Voltage Resolution Differential Nonlinearity DAC Resolution 2 IBR VBR VISRC 0.1 VSS + 1.3 VSS VDD - 1.3 VDD V 5k load to VSS or VDD No load VOUT = (VSS 0.25V) to (VDD - 0.25V) Gain to 10Hz, sensor impedance = 5k, full-span output = 4V VSS + 0.25 VSS 0.02 -1.0 (sink) TA = TMIN to TMAX 54 50 VDD - 0.25 VDD 0.02 1.0 (source) 60 V/V ppm/C V mA %FSO CMRR fCLK 63% of final value From VSS to VDD (Note 4) (Note 5) RIN (Notes 2, 3) VDD IDD RBIAS = 400k, fCLK = 100kHz (Note mA M V/C %VDD dB mV mV/V SYMBOL CONDITIONS MIN TYP MAX UNITS

DIGITAL-TO-ANALOG CONVERTERS Reference voltage = 5.000V Output filter capacitor = 0.1F, fCLK 16 V LSB Bits

(VDD = +5V, VSS = +25C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

ANALOG-TO-DIGITAL CONVERTER ADC Differential Nonlinearity Conversion Time ADC Resolution OUTPUTS (LINDAC, FSOTCDAC) Voltage Swing Current Drive Offset Voltage UNCOMMITTED OP AMP Input Common-Mode Voltage Range Open-Loop Gain Offset Voltage (as unity-gain follower) Output Voltage Swing Output Current Range CMR AV RBIAS = 400k RBIAS = 400k, VIN = 2.5V (no load) 5k load to VSS or VDD No load VOUT = (VSS 0.25V) to (VDD 0.25V) -20 VSS + 0.25 VSS 0.02 -1.0 (sink) VSS VDD - 0.25 VDD 0.02 1.0 (source) VDD V mA VOFS RBIAS = 400k (no load) RBIAS = 400k, VIN = 2.5V, VOUT 2.5V 20mV (VIN - VOUT) at VIN = 2.5V, RBIAS = 400k (no load) VSS VDD A mV VBR to 3.5V, fCLK = 100kHz fCLK 160 12 LSB ms Bits

Note 1: Circuit of Figure 5 with current source turned off. This value is adjustable through a bias resistor and represents the IC current consumption. This excludes the 93C66 EEPROM average current, which is approximately at a refresh rate of 3Hz (fCLK = 100kHz). Note 2: Temperature errors for the entire range are compensated together with the sensor errors. Note 3: The sensor and the MAX1457 must always be at the same temperature during calibration and use. Note 4: This is the maximum allowable sensor offset at minimum gain (54V/V). Note 5: This is the sensor's sensitivity normalized to its drive voltage, assuming a desired full-span output of 4V and a bridge voltage of 2.5V. Lower sensitivities can be accommodated by using the auxiliary op amp. Higher sensitivities can be accommodated by operating at lower bridge voltages.


 

Related products with the same datasheet
MAX1457A
MAX1457ACJ
MAX1457AWI
MAX1457C
MAX1457C/D
MAX1457CCJ
Some Part number from the same manufacture Maxim Integrated Products
MAX1458 1% Accurate, Digitally Trimmed Sensor Signal Conditioner
MAX1459 2-wire, 4-20ma Smart Signal Conditioner
MAX145AC +2.7V, Low-Power, 2-Channel, 108ksps, Serial 12-Bit ADCs in 8-Pin Max
MAX146 +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
MAX1460 Low-Power, 16-Bit Smart ADC
MAX1460C +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
MAX1460CCM Low-Power, 16-Bit Smart ADC
MAX1462 MAX1462 Low-Voltage, Low-Power, 16-Bit Smart ADC
MAX1463 MAX1463 Low-Power, Two-channel Sensor Signal Processor
MAX146AC +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
MAX146EVKIT MAX146EVKIT, MAX147EVKIT Evaluation System/evaluation Kits For The MAX146/MAX147
MAX147 +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
MAX1470 MAX1470 315MHz Low-Power, +3V Superheterodyne Receiver
MAX1470EVKIT MAX1470EVKIT Evaluation Kit For The MAX1470
MAX1471 315MHz/434MHz Low-Power, 3V/5V Ask/fsk Superheterodyne Receiver <<<>>><<<>>>The MAX1471 Low-power, CMOS, Superheterodyne, RF Dual-channel Receiver is Designed to Receive Both Amplitude- Shift-keyed (ASK)
MAX1472 MAX1472 300MHz-to-450MHz Low-Power, Crystal-based Ask Transmitter
MAX1472EVKIT MAX1472EVKIT Evaluation Kit For The MAX1472
MAX1473 MAX1473 315MHz/433MHz, Ask, Superheterodyne Receiver With Extended Dynamic Range
MAX1474 MAX1474 Miniature Electronically Trimmable Capacitor
MAX1478 1% Accurate, Digitally Trimmed, Rail-to-rail Sensor Signal Conditioner
MAX1479 300MHz to 450MHz Low-Power, Crystal-based +10dBm Ask/fsk Transmitter <<<>>>The MAX1479 Crystal-referenced Phase-locked-loop (PLL) VHF/uhf Transmitter is Designed to Transmit Ask, Ook, And FSK Data in The 300MHz

MAX6458UKD3B-T : MAX6457, MAX6458, MAX6459, MAX6460 High-Voltage, Low-current Voltage Monitors in Sot Packages

MAX660EPA : CMOS Monolithic Voltage Converter

DS1337U+ : IC Serial Real-Time Clock The DS1337 serial real-time clock is a low-power clock/calendar with two programmable time-of-day alarms and a programmable square-wave output. Address and data are transferred serially through an IC bus. The clock/calendar provides seconds, minutes, hours, day, date, mo

MAX6502CMN030 : Low-cost, +2.7v to +5.5v, Micropower Temperature Switches in Sot23 and To-220

MAX6464UR54+T : Pmic - Supervisor Integrated Circuit (ics) Simple Reset/Power-On Reset Tape & Reel (TR) 1; IC VOLT DETECTOR LP SOT23-3 Specifications: Output: Push-Pull, Totem Pole ; Reset: Active Low ; Package / Case: TO-236-3, SC-59, SOT-23-3 ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: 1 ; Reset Timeout: 150 ms Minimum ; Type: Simple Reset/Power-On Reset ; Voltage - Threshold: 5.4V ; Operating Temperature: -

MAX6464UK45+T : Pmic - Supervisor Integrated Circuit (ics) Simple Reset/Power-On Reset Tape & Reel (TR) 1; IC VOLT DETECTOR LP SOT23-5 Specifications: Output: Push-Pull, Totem Pole ; Reset: Active Low ; Package / Case: SC-74A, SOT-753 ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: 1 ; Reset Timeout: 150 ms Minimum ; Type: Simple Reset/Power-On Reset ; Voltage - Threshold: 4.5V ; Operating Temperature: -40C ~ 125

MAX6037CAUKADJ+T : Low-power, Fixed and Adjustable Reference with Shutdown in Sot23

ICL7618BESA : OP-AMP, 7000 uV OFFSET-MAX, 0.044 MHz BAND WIDTH, PDSO8 Specifications: Supply Voltage (VS): 5 volts ; IBIAS: 0.0040 µA ; CMRR: 80 dB ; Slew Rate: 0.0160 V/µs ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Package Type: SOP, LEAD FREE, PLASTIC, SOP-8 ; Number of Pins: 8 ; Number of Devices: 1

MAX260BEWG+ : DUAL SWITCHED CAPACITOR FILTER, DIGITALLY PROGRAMMABLE, UNIVERSAL, PDIP24 Specifications: Filter Category: Active Filter ; Filter Type: Universal ; Filter Class: Switched Capacitor ; Supply Voltage (VS): 2.37 to 6.3 volts ; Fc: 1.00E-5 to 10 kHz ; Package Type: DIP, 0.300 INCH, PLASTIC, DIP-24 ; Number of Pins: 24 ; Number of Devices: 2 ; Applications: General

MAX6473TA33AD2-T : FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, DSO8 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed, Adjustable / Variable ; Package Type: Other, 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEC, TDFN-8 ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.23 to 5 volts ; IOUT: 0.3000 amps

 
0-C     D-L     M-R     S-Z