Details, datasheet, quote on part number: HIP6303CB-T
PartHIP6303CB-T
CategoryPower Management => PWM Controllers => Others
TitleBuck Mode
DescriptionMicroprocessor Core Voltage Regulator Multi-phase Buck PWM Controller
CompanyIntersil Corporation
DatasheetDownload HIP6303CB-T datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller

The HIP6303 multi-phase PWM control IC together with its companion gate drivers, the or HIP6603 and Intersil MOSFETs provides a precision voltage regulation system for advanced microprocessors. Multiphase power conversion is a marked departure from earlier single channel converter configurations previously employed to satisfy the ever increasing current demands of modern microprocessors. Multi-phase converters, by distributing the power and load current results in smaller and lower cost transistors with fewer input and output capacitors. These reductions accrue from the higher effective conversion frequency with higher frequency ripple current due to the phase interleaving process of this topology. For example, a three channel converter operating at 350kHz will have a ripple frequency of 1.05MHz. Moreover, greater converter bandwidth of this design results in faster response to load transients. Outstanding features of this controller IC include programmable VID codes from the microprocessor that range from to 2.05V with a system accuracy of 1%. Pull up currents on these VID pins eliminates the need for external pull up resistors. In addition "droop" compensation, used to reduce the overshoot or undershoot of the CORE voltage, is easily programmed with a single resistor. Another feature of this controller IC is the PGOOD monitor circuit which is held low until the CORE voltage increases, during its Soft-Start sequence, to within 10% of the programmed voltage. Over-voltage, 15% above programmed CORE voltage, results in the converter shutting down and turning the lower MOSFETs ON to clamp and protect the microprocessor. Under voltage is also detected and results in PGOOD low if the CORE voltage falls 10% below the programmed level. Over-current protection reduces the regulator current to less than 25% of the programmed trip value. These features provide monitoring and protection for the microprocessor and power system.

Features

AMD Athlon Compatible Multi-Phase Power Conversion Precision Channel Current Sharing - Loss Less Current Sampling - Uses rDS(ON) Precision CORE Voltage Regulation - 1% System Accuracy Over Temperature Microprocessor Voltage Identification Input - 4-Bit VID Input in 50mV Steps - Programmable "Droop" Voltage Fast Transient Recovery Time Over Current Protection Automatic Selection or 4 Channel Operation High Ripple Frequency, (Channel Frequency) Times Number of Channels. to 6MHz

PART NUMBER HIP6303CB-T HIP6303EVAL1 TEMP. (oC) to 70 PACKAGE 20 Ld SOIC PKG. NO. M20.3

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Copyright Intersil Corporation 1999 AthlonTM is a trademark of Advanced Micro Devices, Inc.

POWER-ON RESET (POR) VSEN + UV THREE STATE OV LATCH S + OVP X1.15

Channel frequency, FSW, select and disable. A resistor from this pin to ground sets the switching frequency of the converter. Pulling this pin to ground disables the converter and three states the PWM outputs. See Figure 10.

Bias and reference ground. All signals are referenced to this pin.
Power good monitor input. Connect to the microprocessorCORE voltage.

Voltage Identification inputs from microprocessor. These pins respond to TTL and 3.3V logic signals. The HIP6303 decodes VID bits to establish the output voltage. See Table 1.

PWM outputs for each driven channel in use. Connect these pins to the PWM input a HIP6601/2/3 driver. For systems which use 3 channels, connect PWM4 high. Two channel systems connect PWM3 and PWM4 high.

Enable pin normal operation is with input open or high. A low input disables the regulator and three states the PWM outputs.

Current sense inputs from the individual converter channel's phase nodes. Unused sense lines MUST be left open.

Output of the internal error amplifier. Connect this pin to the external feedback and compensation network.

Power good. This pin provides a logic-high signal when the microprocessor-CORE voltage (VSEN pin) is within specified limits and Soft-Start has timed out.


 

Related products with the same datasheet
HIP6303CB
HIP6303EVAL1
Some Part number from the same manufacture Intersil Corporation
HIP6303EVAL1 Microprocessor Core Voltage Regulator Multi-phase Buck PWM Controller
HIP6304 Microprocessor Core Voltage Regulator Multiphase Buck PWM Controller
HIP6304EVAL1 Microprocessor Core Voltage Regulator Multi-phase Buck PWM Controller
HIP6311
HIP6311A
HIP6311CB
HIP6500 Multiple Linear Power Controller With Acpi Control Interface
HIP6500B
HIP6500CB
HIP6501 Triple Linear Power Controller With Acpi Control Interface
HIP6501A
HIP6501EVAL1
HIP6502 Multiple Linear Power Controller With Acpi Control Interface
HIP6502B
HIP6502CB
HIP6503
HIP6521 PWM And Triple Linear Power Controller
HIP6601 Synchronous-rectified Buck MOSFET Drivers
HIP6601ACB-T
HIP6601B Synchronous Rectified Buck MOSFET Drivers
HIP6601CB Synchronous-rectified Buck MOSFET Drivers

EL5111IYE : Single 60MHz Rail-to-rail Input-output op Amp The EL5111 is a Low Power, High Voltage Rail-to-rail Input-output Single Amplifier. Operating on Supplies Ranging From 5V to 15V, While Consuming Only 2.5mA Per Amplifier, The EL5111 Has a Bandwidth of 60MHz (-3dB). It Also Provides Common M

EL5293ACY-T13 : op Amp, Dual 300MHz, Current Feedback, Low Power

HI0390 :

ISL54005IRTZ : Integrated Audio Amplifier Systems The Intersil ISL54003, ISL54005, ISL54006 family of devices are integrated audio power amplifier systems that combine a mono BTL amplifier and stereo headphone amplifiers in a single device. The devices are designed to operate from a single +2.7V to +5V power supp

ISL6115AIBZ : 12V Power Distribution Controllers This fully featured hot swap power controller targets +12V applications. The ISL6115A with its integrated charge pump has a higher (6.5V vs 5V) gate drive than its sister part the ISL6115 making this part an immediate efficiency improvement replacement. This IC

ISL60007DIB812 : Precision 2.50v, 1.08u-watt, High Precision FGA Voltage References

ISL6561CRZA-T : Multi-phase PWM Controller with Precision Rds(on) or DCR Differential Current Sensing for Vr10.x Application

X9251UP24I : Single Supply/low Power/256-tap/spi Bus

X9315WMI-2.7 : Data Acquisition - Digital Potentiometer Integrated Circuit (ics) Non-Volatile Tube 2.7 V ~ 5.5 V; IC DIGITAL POT 10K 32TP 8MSOP Specifications: Number of Circuits: 1 ; Resistance (Ohms): 10K ; Interface: 3-Wire Serial (Chip Select, Increment, Up/Down) ; Taps: 32 ; Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width) ; Packaging: Tube ; Voltage - Supply: 2.7 V ~ 5.5 V ; Memory Type: Non-Volatile ; Temperature Coefficient:

X4285PI-2.7A : Pmic - Supervisor Integrated Circuit (ics) Simple Reset/Power-On Reset Tube 1; IC SUPERVISOR CPU 128K EE 8-DIP Specifications: Output: Open Drain or Open Collector ; Reset: Active High ; Package / Case: 8-DIP (0.300", 7.62mm) ; Packaging: Tube ; Number of Voltages Monitored: 1 ; Reset Timeout: 100 ms Minimum ; Type: Simple Reset/Power-On Reset ; Voltage - Threshold: 2.92V ; Operating Temperature: -40C ~ 85

5962R9672302VXC : 4000/14000/40000 SERIES, DUAL MONOSTABLE MULTIVIBRATOR, CDFP16 Specifications: Supply Voltage: 5V ; Features: Complementary Output ; Package Type: Other, CERAMIC, FP-16 ; Logic Family: CMOS ; Number of Pins: 16 ; Propagation Delay: 810 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F)

 
0-C     D-L     M-R     S-Z