Details, datasheet, quote on part number: HIP4086AB
PartHIP4086AB
CategoryPower Management and Supplies => Gate Drivers => 6417123
TitleHALF BRDG BASED MOSFET DRIVER, PDSO24
Description
CompanyIntersil Corporation
DatasheetDownload HIP4086AB datasheet
Quote
Find where to buy
 
Specifications 
Driver TypeHigh-side, Dual Gate Driver
Supply Voltage7 to 15 volts
Rise Time100 ns
Fall Time100 ns
Operating Temperature-40 to 125 C (-40 to 257 F)
Package TypeSOIC, ROHS COMPLIANT, PLASTIC, MS-013AD, SOIC-24
Production StatusFull-Production
Screening LevelOther, AUTOMOTIVE

 

Features, Applications

The HIP4086 and HIP4086A (referred to as the HIP4086/A) are three phase N-Channel MOSFET drivers. Both parts are specifically targeted for PWM motor control. These drivers have flexible input protocol for driving every possible switch combination. The user can even override the shoot-through protection for switched reluctance applications. The HIP4086/A have a wide range of programmable dead times to 4.5ms) which makes them very suitable for the low frequencies (up to 100kHz) typically used for motor drives. The only difference between the HIP4086 and the HIP4086A is that the HIP4086A has the built-in charge pumps disabled. This is useful in applications that require very quiet EMI performance (the charge pumps operate at 10MHz). The advantage of the HIP4086 is that the built-in charge pumps allow indefinitely long on times for the high-side drivers. To insure that the high-side driver boot capacitors are fully charged prior to turning on, a programmable bootstrap refresh pulse is activated when VDD is first applied. When active, the refresh pulse turns on all three of the low-side bridge FETs while holding off the three high-side bridge FETs to charge the high-side boot capacitors. After the refresh pulse clears, normal operation begins. Another useful feature of the HIP4086/A is the programmable undervoltage set point. The set point range varies from to 8.5V.

Features

Independently drives 6 N-Channel MOSFETs in three phase bridge configuration Bootstrap supply max voltage to 95VDC with bias supply from 15V 1.25A peak turn-off current User programmable dead time to 4.5s) Bootstrap and optional charge pump maintain the high-side driver bias voltage. Programmable bootstrap refresh time Drives 1000pF load with typical rise time of 20ns and Fall Time of 10ns Programmable undervoltage set point

Applications

Brushless Motors (BLDC) 3-phase AC motors Switched reluctance motor drives Battery powered vehicles Battery powered tools


CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-468-3774 | Copyright Intersil Americas Inc. 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners.

HIP4086, HIP4086A Block Diagram (for clarity, only one phase is shown)

If under voltage is active or if DIS is asserted, the high and low-side drivers are turned off. drive enable common with all phases Adjustable Turn-on Delay 10 nSec delay Under Voltage Detector delay disable Refresh Pulse common with all phases Adjustable Turn-on Delay

Level Shifter *The charge pump is permanently disabled in the HIP4086A.

If the voltage on RDEL is less than 100 mV, the turn-on delay timers are disabled and the high and low-side drivers can be turned on simultaneously.

INPUT ALI, BLI, CLI X AHI, BHI, CHI UV X DIS 1 X RDEL X <100mV OUTPUT ALO, BLO, CLO AHO, BHO, CHO

PIN NUMBER SYMBOL AHB BHB CHB (xHB) AHS BHS CHS (xHS) AHI BHI CHI (xHI) DESCRIPTION High-Side Bias Connections. One external bootstrap diode and one capacitor are required for each. Connect cathode of bootstrap diode and positive side of bootstrap capacitor to each xHB pin. High-Side Source Connections. Connect the sources of the High-Side power MOSFETs to these pins. The negative side of the bootstrap capacitors are also connected to these pins.

High-Side Logic Level Inputs. Logic at these three pins controls the three high side output drivers, AHO (Pin 17), BHO (Pin 24) and CHO (Pin 14). When xHI is low, xHO is high. When xHI is high, xHO is low. Unless the dead time is disabled by connecting RDEL (Pin 7) to ground, the low side input of each phase will override the corresponding high side input on that phase see "Truth Table" on page 2. If RDEL is tied to ground, dead time is disabled and the outputs follow the inputs with no shoot-thru protection. DIS (Pin 10) also overrides the high side inputs. xHI can be driven by signal levels to 15V (no greater than VDD). Low-Side Logic Level Inputs. Logic at these three pins controls the three low-side output drivers ALO (Pin 21), BLO (Pin 22) and CLO (Pin 19). If the upper inputs are grounded then the lower inputs control both xLO and xHO drivers, with the dead time set by the resistor at RDEL (Pin 7). DIS (Pin 10) high level input overrides xLI, forcing all outputs low. xLI can be driven by signal levels to 15V (no greater than VDD). Ground. Connect the sources of the Low-Side power MOSFETs to this pin. Delay Time Set point. Connect a resistor from this pin to VDD to set timing current that defines the dead time between drivers - see Figure 17. All drivers turn-off with minimal delay, RDEL resistor prevents shoot-through by delaying the turn-on of all drivers. When RDEL is tied to VSS, both upper and lowers can be commanded on simultaneously. While not necessary in most applications, a decoupling capacitor 0.1F or smaller may be connected between RDEL and VSS. Under voltage Set point. A resistor can be connected between this pin and VSS to program the under voltage set point, see Figure 18. With this pin not connected, the under voltage disable is typically 6.6V. When this pin is tied to VDD , the under voltage disable is typically 6.2V. Refresh Pulse Setting. An external capacitor can be connected from this pin to VSS to increase the length of the start up refresh pulse - see Figure 16. If this pin is not connected, the refresh pulse is typically 1.5s. Disable Input. Logic level input that when taken high sets all six outputs low. DIS high overrides all other inputs. With DIS low, the outputs are controlled by the other inputs. DIS can be driven by signal levels to 15V (no greater than VDD).


 

Related products with the same datasheet
HIP4086AABZ-T
HIP4086AB-T
HIP4086ABT
HIP4086ABZ
HIP4086ABZ-T
HIP4086ABZT
HIP4086APZ
HIP4086APZ-T
Some Part number from the same manufacture Intersil Corporation
HIP4086AB-T Specifications: Driver Type: High-side, Dual Gate Driver ; Supply Voltage: 7 to 15 volts ; Rise Time: 100 ns ; Fall Time: 100 ns ; Operating Temperature: -40 to 125 C (-40 to 257 F) ; Package Type: SOIC,
HS0-117EH-Q Specifications: Regulator Type: Standard ; Output Polarity: Positive ; Output Voltage Type: Adjustable / Variable ; Life Cycle Stage: ACTIVE
HS0-1825ARH/SAMPLE Specifications: Configuration / Function: Boost ; Package Type: Other, DIE-16 ; Life Cycle Stage: ACTIVE ; IOUT: 1 amps ; VIN: 12 to 30 volts ; fsw: 500 kHz ; Operating Temperature: -50 to 125 C (-58 to 257 F)
HS0-1840AEH-Q
HS0-26C32RH-Q Specifications: Technology: RS422, CMOS ; Device Type: Receiver ; Supply Voltage: 5V ; Package Type: DIE-16 ; Pins: 16 ; Features: RoHS
HS0-303BRH-Q Specifications: Supply Voltage (VS): -12 to 12 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Logic Family: CMOS ; Package Type: DIE-13 ; Number of Pins: 13 ; Number of Devices: 2
HS1-1840ARH/PROTO Specifications: Applications: Military ; Supply Voltage (VS): -15.5 to 16 volts ; Ron: 4000 ohms ; tON: 3000 ns ; tOFF: 3000 ns ; VISO: 45 dB ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package
HS1-26CT31RH/PROTO Specifications: Technology: RS422, CMOS ; Device Type: Line / Bus Driver ; Supply Voltage: 5V ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: DIP, SIDE BRAZED, CERAMIC, DIP-16 ; Pins:
HS1-303BRH/PROTO Specifications: Supply Voltage (VS): -12 to 12 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Logic Family: CMOS ; Package Type: SBDIP-14 ; Number of Pins: 14 ; Number of Devices: 2
HS2-117EH-Q Specifications: Regulator Type: Standard ; Output Polarity: Positive ; Output Voltage Type: Adjustable / Variable ; Life Cycle Stage: ACTIVE
HS2-3530ARH/PROTO Specifications: Supply Voltage (VS): 3 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: METAL CAN-8 ; Number of Pins: 8 ; Number of Devices: 1
HS7B-1135RH/PROTO Specifications: Supply Voltage (VS): 5 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: DIP, ROHS COMPLIANT, SIDE BRAZED, CERAMIC, DIP-8 ; Number of Devices: 1
HS9-1135RH-Q
HS9-1825ARH/PROTO Specifications: Configuration / Function: Boost ; Package Type: Other, CERAMIC, FP-16 ; Life Cycle Stage: ACTIVE ; IOUT: 1 amps ; VIN: 12 to 30 volts ; fsw: 500 kHz ; Operating Temperature: -50 to 125 C (-58
HS9-1840ARH/PROTO Specifications: Applications: Military ; Supply Voltage (VS): -15.5 to 16 volts ; Ron: 4000 ohms ; tON: 3000 ns ; tOFF: 3000 ns ; VISO: 45 dB ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package
HS9-26CT31RH/PROTO Specifications: Technology: RS422, CMOS ; Device Type: Line / Bus Driver ; Supply Voltage: 5V ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: CERAMIC, FP-16 ; Pins: 16
HS9-303BRH/PROTO Specifications: Supply Voltage (VS): -12 to 12 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Logic Family: CMOS ; Package Type: FP-14 ; Number of Pins: 14 ; Number of Devices: 2
HS9-3530ARH/PROTO Specifications: Supply Voltage (VS): 3 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: CERAMIC, DFP-10 ; Number of Pins: 10 ; Number of Devices: 1
HS9-4080ARH/PROTO Specifications: Driver Type: FULL BRDG BASED MOSFET DRIVER ; Supply Voltage: 12 to 18 volts ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: CERAMIC, DFP-20 ; Production Status: Full-Production
HS9-4423BRH/PROTO Specifications: Driver Type: BUF OR INV BASED MOSFET DRIVER ; Output Current: 2 amps ; Supply Voltage: 12 to 18 volts ; Rise Time: 250 ns ; Fall Time: 250 ns ; Operating Temperature: -55 to 125 C (-67
HS9-5104ARH/PROTO Specifications: Slew Rate: 2 V/µs ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Package Type: CERAMIC, DFP-14 ; Number of Pins: 14 ; Number of Devices: 4 ; Standards: RoHS

HD-15530-9 : CMOS Manchester Encoder-decoder

ISL9000AIRFJZ : Dual LDO with Low Noise, Very High Psrr, and Low IQ

HA2-2529/883 : Precision, High Slew Rate, Wideband Operational Amplifier

ISL6415IR : Triple Output Regulator with Single Synchronous Buck and Dual LDO

DG433A : 2 Channel Drivers WITH SPST AND DPST FET Switches

X40020S14I-B : Pmic - Supervisor Integrated Circuit (ics) Multi-Voltage Supervisor Tube 2; IC VOLTAGE MONITOR DUAL 14-SOIC Specifications: Output: Open Drain or Open Collector ; Reset: Active High ; Package / Case: 14-SOIC (0.154", 3.90mm Width) ; Packaging: Tube ; Number of Voltages Monitored: 2 ; Reset Timeout: Adjustable/Selectable ; Type: Multi-Voltage Supervisor ; Voltage - Threshold: 2.9V, 4.6V ; Operating Tempera

ISL6298EVAL1 : Eval And Demo Board And Kit Programmers, Development System; EVALUATION BOARD 1 ISL6298 Specifications: Main Purpose: Power Management, Battery Charger ; Primary Attributes: - ; Secondary Attributes: - ; Supplied Contents: Board ; Utilized IC / Part: ISL6298 ; Embedded: - ; Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant

ISL78235AARZ-T7A : Voltage Regulators - Switching Regulators Auto 5A Sync Buck Regulator Intersil ISL7823x Compact Synchronous Buck Regulators are highly efficient, monolithic, synchronous step-down DC/DC converters. The ISL78233 delivers 3A, ISL78234 4A, and the ISL78235 5A with continuous output currents from a 2.7-5.5V input supply. The ISL7823x use current mode control architectu

 
0-C     D-L     M-R     S-Z