Details, datasheet, quote on part number: IDT74FCT540AT
PartIDT74FCT540AT
CategoryLogic => Line Driver/Receivers => CMOS/BiCMOS->FCT/FCT-T Family
TitleCMOS/BiCMOS->FCT/FCT-T Family
DescriptionFast CMOS Octal Buffer/line Driver
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT74FCT540AT datasheet
Quote
Find where to buy
 
  

 

Features, Applications

A and C grades Low input and output leakage 1A (max.) CMOS power levels True TTL input and output compatibility: VOH = 3.3V (typ.) VOL = 0.3V (typ.) High Drive outputs (-15mA IOH, 64mA IOL) Meets or exceeds JEDEC standard 18 specifications Power off disable outputs permit "live insertion" Available in SOIC, SSOP, and QSOP packages

The IDT octal buffer/line driver is built using an advanced dual metal CMOS technology. The FCT540T is similar in function to the FCT240T, except that the inputs and outputs are on opposite sides of the package. This pinout arrangement makes these devices especially useful as output ports for microprocessors and as backplane drivers, allowing ease of layout and greater board density.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Symbol VTERM(2) VTERM(3) TSTG IOUT Description Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Storage Temperature DC Output Current Max to +120 Unit C mA

NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. No terminal voltage may exceed Vcc by +0.5V unless otherwise noted. 2. Inputs and Vcc terminals only. 3. Output and I/O terminals only.

Symbol CIN Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 6 8 Max. 10 12 Unit pF COUT

NOTE: 1. This parameter is measured at characterization but not tested.
Pin Names OEA, OEB Dx Ox Inputs Outputs Description 3-State Output Enable Inputs (Active LOW)
NOTE: H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High Impedance
Following Conditions Apply Unless Otherwise Specified: Industrial: to +85C, VCC 5.0V 5%

Symbol VIH VIL IIH IIL IOZH IOZL II VIK VH ICC Parameter Input HIGH Level Input LOW Level Input HIGH Current(4) Input LOW Current(4) High Impedance Output Current(4) (3-State Output pins)(4) Input HIGH Current(4) Clamp Diode Voltage Input Hysteresis Quiescent Power Supply Current VCC = Max. VIN = GND or VCC = Max., VI = VCC (Max.) VCC = Min., IIN = 18mA Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VCC = Max. VCC = Max. = 0.5V Min. 200 0.01 Max. mV mA Unit V A

Symbol VOH VOL IOS Parameter Output HIGH Voltage Output LOW Voltage Short Circuit Current VCC = Min VIN = VIH or VIL VCC = Min VIN = VIH or VIL Test Conditions(1) IOH = 8mA IOH = 15mA IOL = 64mA Min. 60 Typ.(2) Max. 0.55 225 Unit V mA

NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. The test limit for this parameter = 55C.


 

Related products with the same datasheet
IDT74FCT540ATD
IDT74FCT540ATDB
IDT74FCT540ATE
IDT74FCT540ATEB
IDT74FCT540ATL
IDT74FCT540ATLB
IDT74FCT540ATP
IDT74FCT540ATPB
IDT74FCT540ATPY
IDT74FCT540ATPYB
IDT74FCT540CT
IDT74FCT540CTD
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT74FCT540ATD Fast CMOS Octal Buffer/line Driver
IDT74FCT540ATQ Octal Buffer/line Driver
IDT74FCT540C Fast CMOS Octal Buffer/line Driver
IDT74FCT540CT
IDT74FCT540CTQ Octal Buffer/line Driver
IDT74FCT540D Fast CMOS Octal Buffer/line Driver
IDT74FCT540TD Fast Smos Octal Buffer/line Driver
IDT74FCT540TDB
IDT74FCT540TE
IDT74FCT540TEB
IDT74FCT540TL
IDT74FCT540TLB
IDT74FCT540TP
IDT74FCT540TPB
IDT74FCT540TPY
IDT74FCT540TPYB
IDT74FCT540TQ
IDT74FCT540TQB
IDT74FCT540TSOB
IDT74FCT541 Fast CMOS Octal Buffer/line Driver
IDT74FCT541ASO Octal Buffer/line Driver

IDT7217L75F : 16 X 16 Parallel CMOS Multipliers

IDT72V231L20J : 256 X 9 Syncfifo, 3.3V

IDT74FCT22245ATSO : Fast CMOS Octal Bidirectional Transceivers

IDT7142LA20FG : HIGH SPEED 2K X 8 DUAL PORT STATIC RAM The IDT7132/IDT7142 are high-speed 2K x 8 Dual-Port Static RAMs. The IDT7132 is designed to be used as a stand-alone 8-bit Dual-Port RAM or as a “MASTER? Dual-Port RAM together with the IDT7142 “SLAVE? Dual-Port in 16-bit-or-more word width systems.

IDT7026S20GG : 16K X 16 DUAL-PORT SRAM, 15 ns, CPGA84 Specifications: Memory Category: SRAM Chip ; Density: 262 kbits ; Number of Words: 16 k ; Bits per Word: 16 bits ; Package Type: CERAMIC, PGA-84 ; Pins: 84 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 15 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT72205LB15J : 256 X 8 OTHER FIFO, 6.5 ns, UUC28 Specifications: Memory Category: FIFO ; Density: 2 kbits ; Number of Words: 256 k ; Bits per Word: 8 bits ; Package Type: DIE ; Pins: 28 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 6.5 ns ; Cycle Time: 10 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT723646L15PFG8 : 1K X 36 OTHER FIFO, 11 ns, PQFP120 Specifications: Memory Category: FIFO ; Density: 37 kbits ; Number of Words: 1 k ; Bits per Word: 36 bits ; Package Type: TQFP, TQFP-120 ; Pins: 120 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 11 ns ; Cycle Time: 15 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT7280L30TPB : 256 X 9 OTHER FIFO, 12 ns, PQCC32 Specifications: Communication Type: Asynchronous ; Production Status: Full Production ; Density: 2 kbits ; Number of Words: 256 k ; Bits per Word: 9 bits ; Access Time: 12 ns ; Logic Family: CMOS ; Supply Voltage: 5V ; Package Type: PLASTIC, LCC-32 ; Operating Range: Commercial ; Pins: 32 ; Operatin

TTS92256GK-20M-2 : IC,SRAM,32KX8,CMOS,FP,28PIN,CERAMIC Specifications: Memory Category: SRAM Chip

72V285L15PFI9 : 64K X 18 OTHER FIFO, 6.5 ns, PQFP64 Specifications: Memory Category: FIFO ; Density: 1180 kbits ; Number of Words: 64 k ; Bits per Word: 18 bits ; Package Type: TQFP, PLASTIC, TQFP-64 ; Pins: 64 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 6.5 ns ; Cycle Time: 10 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

72V81L15PA : 512 X 9 BI-DIRECTIONAL FIFO, 15 ns, PDSO56 Specifications: Memory Category: FIFO ; Density: 5 kbits ; Number of Words: 512 k ; Bits per Word: 9 bits ; Package Type: TSSOP, TSSOP-56 ; Pins: 56 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 15 ns ; Cycle Time: 25 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

Same catergory

5962-9861101Q2A : Inverting Buffers and Drivers. ti SN54128, Line Drivers.

ACS253MS : Multiplexers->CMOS/BiCMOS->AC/ACT Family. Radiation Hardened Dual 4-input Multiplexer With Three-state Outputs.

AVGDV74LS259N : 8 Bit Addressable Latch, Plastic Dip, Through Hole.

HD74LS152 : Multiplexers. 1-of-8 Line Data Selector/multiplexer. Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp. The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog and discrete devices, and memory chips.

IDT54FCT827AD : High-performance CMOS Buffers. Faster than AMD's Am29827 series Equivalent to AMD's Am29827 bipolar buffers in pinout/ function, speed and output drive over full temperature and voltage supply extremes IDT54/74FCT827A equivalent to FASTTM IDT54/74FCT827B 35% faster than FAST IDT54/74FCT827C 45% faster than FAST IOL = 48mA (commercial), and 32mA (military) Clamp diodes on all inputs.

IN74ACT640DW : Octal Bus Transceiver (3-State) 20. The IN74ACT640 is identical in pinout to the LS/ALS640, HC/HCT640. The IN74ACT640 may be used as a level converter for interfacing TTL or NMOS outputs to High Speed CMOS inputs. The a 3-state transceiver that is used for 2-way asynchronous communication between data buses. The device has an active-low Output Enable pin, which is used to place the I/O ports.

PI74FCT162344T : CMOS/BiCMOS->FCT/FCT-T Family. Fast CMOS Address/clock Driver. Ideal for address line driving and clock distribution Eight banks with 1:4 fanout with 3-state control Typical tSK(O) output skew < 500ps Balanced output drivers: 24mA Hysteresis on all inputs Packages available: 56-pin 240-mil wide plastic TSSOP (A) 56-pin 300-mil wide plastic SSOP (V) Pericom Semiconductor's PI74FCT series of logic circuits are produced.

SL74HC109 : Dual J-k Flip-flop With Set And Reset. The SL74HC109 is identical in pinout to the LS/ALS109. The device inputs are compatible with standard CMOS outputs, with pullup resistors, they are compatible with LS/ALSTTL outputs. This device consists of two J-K flip-flops with individual set, reset, and clock inputs. Changes at the inputs are reflected at the outputs with the next low-to-high transition.

SN54F283FK : 4-bit Binary Full Adders With Fast Carry. SN74F283 4-BIT BINARY FULL ADDERS WITH FAST CARRY Full-Carry Look-Ahead Across the Four Bits Systems Achieve Partial Look-Ahead Performance With the Economy of Ripple Carry Package Options Include Plastic Small-Outline Packages, Ceramic Chip Carriers, and Standard Plastic and Ceramic 300-mil DIPs The is a full adder that performs the addition of two 4-bit.

SN74LV14 : CMOS/BiCMOS->LV/LVQ/LVX Family->Low Voltage. Hex Schmitt-trigger.

SN74SSTV16859 : . Member of Texas Instruments Widebus Family 1-to-2 Outputs to Support Stacked DDR DIMMs Supports SSTL_2 Data Inputs Outputs Meet SSTL_2 Class II s Differential Clock (CLK and CLK) Inputs Supports LVCMOS Switching Levels on the RESET Input RESET Input Disables Differential Input Receivers, Resets All Registers, and Forces All Outputs Low Pinout Optimizes.

SN74AUP1G74 : Low-Power Single Positive-Edge-Triggered D-Type Flip-Flop * Available in the Texas Instruments NanoStar and NanoFree Packages * Low Static-Power Consumption: ICC = 0.9 A Max * Low Dynamic-Power Consumption: Cpd = 4.3 pF Typ at 3.3 V * Low Input Capacitance: Ci = 1.5 pF Typ * Low Noise Overshoot and Undershoot .

AH1822-FT4 : Omnipolar - Switches Low Power Omnipolar. Micropower operation Operation with magnetic field of either north or south pole (omnipolar) to 5.5V battery operation Chopper stabilized Superior temperature stability Extremely Low Switch-Point Drift Insensitive to Physical Stress Good RF noise immunity to 85C operating temperature ESD (HBM) 5KV DFN2015-6 and DFN3020-6: Available in "Green" Molding.

MAX3370 : 1A, 2Mbps, Low-Voltage Level Translators In SC70 And DFN The MAX3370/MAX3371 logic-level translators are ideal for applications interfacing low-voltage devices to other logic levels. Externally applied voltages set the logic levels of the MAX3370/MAX3371. The devices accept VCC from +2.5V to +5.5V and VL from +1.6V to +5.5V, allowing data transfer.

ATF22LV10C-10DC : FLASH PLD, 10 ns, CDIP24. s: Package Type: CDIP, Other, 0.300 INCH, WINDOWED, CERDIP-24 ; Pins: 24 ; Logic Family: CMOS ; User I/Os: 10 pins ; Propagation Delay: 10 ns ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Supply Voltage: 5V.

HD74ALVC1G00VS : ALVC/VCX/A SERIES, 2-INPUT NAND GATE, PDSO5. s: Gate Type: NAND ; Supply Voltage: 1.5V ; Logic Family: CMOS ; Inputs: 2 ; Propagation Delay: 8 ns ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Pin Count: 5 ; IC Package Type: Other, VSON-5.

935210640118 : LVC/LCX/Z SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PDSO20. s: Flip-Flop Type: D ; Triggering: Positive-edge Triggered ; Supply Voltage: 2.7 ; Output Characteristics: TRUE ; Propagation Delay: 11.2 ns ; fMAX: 125 MHz ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: 7.50 MM, PLASTIC, MS-013AC, SOT-163-1, SO-20 ; Logic.

 
0-C     D-L     M-R     S-Z