Details, datasheet, quote on part number: IDT54FCT162H244CT
PartIDT54FCT162H244CT
Category
DescriptionFast CMOS 16-bit Buffer/line Driver
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT162H244CT datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Common features: 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) 250ps Low input and output leakage 1 A (max.) ESD > 2000V per MIL-STD-883, Method > 200V using machine model 0) Packages include 25 mil pitch SSOP, 19.6 mil pitch TSSOP, 15.7 mil pitch TVSOP and 25 mil pitch Cerpack Extended commercial range to +85C Features for FCT16244T/AT/CT/ET: High drive outputs (-32mA IOH, 64mA IOL) Power off disable outputs permit "live insertion" Typical VOLP (Output Ground Bounce) 1.0V at VCC = 25C Features for FCT162244T/AT/CT/ET: Balanced Output Drivers: 24mA (commercial), 16mA (military) Reduced system switching noise Typical VOLP (Output Ground Bounce) 0.6V at VCC = 25C Features for FCT166244T/AT/CT: Light Drive Balanced Output: 8mA (commercial), 6mA (military) Minimal system switching noise Typical VOLP (Output Ground Bounce) 0.25V at VCC = 25C Features for FCT162H244T/AT/CT/ET: Bus-Hold retains last active bus state during 3-state Eliminates the need for external pull up resistors

The 16-Bit Buffer/Line Driver is for bus interface or signal buffering applications requiring high speed and low power dissipation. These devices have a flow through pin organization, and shrink packaging to simplify board layout. All inputs are designed with hysteresis for improved noise margin. The three-state controls allow independent 8-bit or combined 16-bit operation. These parts are plug in replacements for 54/74ABT16244 where higher speed, lower noise or lower power dissipation levels are desired. The FCT16244T/AT/CT/ET are ideally suited for driving high capacitance loads (>200pF) and low impedance backplanes. These "high drive" buffers are designed with power off disable capability to allow "live insertion" of boards when used in a backplane interface. The FCT162244T/AT/CT/ET have balanced output current levels and current limiting resistors. These offer low ground bounce, minimal undershoot, and controlled output fall times, reducing the need for external series terminating resistors while still providing very high speed operation for loads of less than 200pF. The FCT166244T/AT/CT are suited for very low noise, point-to-point driving where there is a single receiver, or a very light lumped load (<100pF). The buffers are designed to limit the output current to levels which will avoid noise and ringing on the signal lines without using external series terminating resistors. The FCT162H244T/AT/CT/ET have "Bus-Hold" which retains the input's last state whenever the input goes to high impedance. This prevents "floating" inputs and eliminates the need for pull-up/down resistors.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Pin Names xOE xAx xYx Description 3State Output Enable Inputs (Active LOW) Data Inputs(1) 3-State Outputs

2544 tbl 01 NOTE: On FCT16xH these pins have "Bus-hold". All other pins are standard inputs, outputs or I/Os.

Symbol Description Max. VTERM(2) Terminal Voltage with Respect to +7.0 GND (3) Terminal Voltage with Respect to VTERM 0.5 to GND VCC +0.5 TSTG Storage Temperature +150 I OUT DC Output Current to +120 Unit C mA

NOTE: H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High Impedance

2544 lnk 03 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXXT and FCT166XXXT output and I/O terminals. 3. Output and I/O terminals for FCT162XXXT and FCT166XXXT.

Symbol Parameter(1) CIN Input Capacitance COUT Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. Unit pF 8.0

NOTE: 1. This parameter is measured at characterization but not tested.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (STANDARD PARTS)

Following Conditions Apply Unless Otherwise Specified: Commercial: to +85C, VCC 10%; Military: to +125C, VCC 10%

Symbol VIH VIL L I OZH I OZL VIK VH I CCL I CCH I CCZ Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(5) Input HIGH Current (I/O pins)(5) Input LOW Current (Input pins)(5) VCC = Max. VCC = Min., IIN = 18mA VCC = Max., VO = GND (3)

Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC VI = GND = 0.5V

Input LOW Current (I/O pins)(5) High Impedance Output Current (3-State Output pins) (5) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current

NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter = 55C.


 

Related products with the same datasheet
IDT54FCT162H244ET
IDT54FCT162H244T
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT162H244CTE Fast CMOS 16-bit Buffer/line Driver
IDT54FCT162H244ET
IDT54FCT162H244ETE
IDT54FCT162H244T
IDT54FCT162H244TE
IDT54FCT162H245 Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245AT Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245ATE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245CT Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245CTE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245ET Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245ETE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245T Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245TE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H272AT Fast CMOS 12-bit Synchronous Bus Exchanger
IDT54FCT162H501 Fast CMOS 18-bit Registered Transceiver
IDT54FCT162H501AT

IDT6168LA45SOB : CMOS Static RAM 16k ( 4k X 4-bit )

IDT89HPES24NT3ZBBXG8 : Specialized Ic Integrated Circuit (ics) PCI Express Switch - Gen1 Tape & Reel (TR); IC PCI SW 24LANE 3PORT 420-SBGA Specifications: Type: PCI Express Switch - Gen1 ; Applications: Server, Storage, Communications, Embedded, Consumer ; Package / Case: 420-LBGA ; Packaging: Tape & Reel (TR) ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

IDT71V25761YSA166BGI8 : ** New ** 3.3V 128K X 36 Synchronous Pipelined Burst SRAM With 2.5V I/o

IDT71V65703S85PFGI : ZBT (Zero Bus Turnaround) SRAM 3.3V 256K X 36 ZBT Synchronous 3.3V I/o Flowthrough SRAM

IDTHS221P10NDGI8 : Interface - Analog Switches, Multiplexers, Demultiplexer Integrated Circuit (ics); IC SWITCH DUAL SPST 10UMLP Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ICS557G-07T : 557 SERIES, LOW SKEW CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 Specifications: Device Type: Clock Driver ; Package Type: Surface Mount, TSSOP, 0.173 INCH, TSSOP-16 ; Supply Voltage: 3.14 to 3.46 volts ; Frequency: 200 MHz ; Operating Temperature: 0.0 to 70 C (32 to 158 F)

IDTQS3VH16233PAG : QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14 Specifications: Device Type: Line / Bus Driver ; Supply Voltage: 3.3V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: SOIC, SOIC-14 ; Pins: 14

71V2546S100PFGI8 : 128K X 36 ZBT SRAM, 5 ns, PBGA119 Specifications: Memory Category: SRAM Chip ; Density: 4719 kbits ; Number of Words: 128 k ; Bits per Word: 36 bits ; Package Type: BGA, 14 X 22 MM, PLASTIC, MS-028AA, BGA-119 ; Pins: 119 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 5 ns ; Operating Temperature: -40 to 70 C (-40 to 158

 
0-C     D-L     M-R     S-Z