Details, datasheet, quote on part number: IDT54FCT162H244AT
PartIDT54FCT162H244AT
Category
DescriptionFast CMOS 16-bit Buffer/line Driver
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT162H244AT datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Common features: 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) 250ps Low input and output leakage 1 A (max.) ESD > 2000V per MIL-STD-883, Method > 200V using machine model 0) Packages include 25 mil pitch SSOP, 19.6 mil pitch TSSOP, 15.7 mil pitch TVSOP and 25 mil pitch Cerpack Extended commercial range to +85C Features for FCT16244T/AT/CT/ET: High drive outputs (-32mA IOH, 64mA IOL) Power off disable outputs permit "live insertion" Typical VOLP (Output Ground Bounce) 1.0V at VCC = 25C Features for FCT162244T/AT/CT/ET: Balanced Output Drivers: 24mA (commercial), 16mA (military) Reduced system switching noise Typical VOLP (Output Ground Bounce) 0.6V at VCC = 25C Features for FCT166244T/AT/CT: Light Drive Balanced Output: 8mA (commercial), 6mA (military) Minimal system switching noise Typical VOLP (Output Ground Bounce) 0.25V at VCC = 25C Features for FCT162H244T/AT/CT/ET: Bus-Hold retains last active bus state during 3-state Eliminates the need for external pull up resistors

The 16-Bit Buffer/Line Driver is for bus interface or signal buffering applications requiring high speed and low power dissipation. These devices have a flow through pin organization, and shrink packaging to simplify board layout. All inputs are designed with hysteresis for improved noise margin. The three-state controls allow independent 8-bit or combined 16-bit operation. These parts are plug in replacements for 54/74ABT16244 where higher speed, lower noise or lower power dissipation levels are desired. The FCT16244T/AT/CT/ET are ideally suited for driving high capacitance loads (>200pF) and low impedance backplanes. These "high drive" buffers are designed with power off disable capability to allow "live insertion" of boards when used in a backplane interface. The FCT162244T/AT/CT/ET have balanced output current levels and current limiting resistors. These offer low ground bounce, minimal undershoot, and controlled output fall times, reducing the need for external series terminating resistors while still providing very high speed operation for loads of less than 200pF. The FCT166244T/AT/CT are suited for very low noise, point-to-point driving where there is a single receiver, or a very light lumped load (<100pF). The buffers are designed to limit the output current to levels which will avoid noise and ringing on the signal lines without using external series terminating resistors. The FCT162H244T/AT/CT/ET have "Bus-Hold" which retains the input's last state whenever the input goes to high impedance. This prevents "floating" inputs and eliminates the need for pull-up/down resistors.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Pin Names xOE xAx xYx Description 3State Output Enable Inputs (Active LOW) Data Inputs(1) 3-State Outputs

2544 tbl 01 NOTE: On FCT16xH these pins have "Bus-hold". All other pins are standard inputs, outputs or I/Os.

Symbol Description Max. VTERM(2) Terminal Voltage with Respect to +7.0 GND (3) Terminal Voltage with Respect to VTERM 0.5 to GND VCC +0.5 TSTG Storage Temperature +150 I OUT DC Output Current to +120 Unit C mA

NOTE: H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High Impedance

2544 lnk 03 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXXT and FCT166XXXT output and I/O terminals. 3. Output and I/O terminals for FCT162XXXT and FCT166XXXT.

Symbol Parameter(1) CIN Input Capacitance COUT Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. Unit pF 8.0

NOTE: 1. This parameter is measured at characterization but not tested.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (STANDARD PARTS)

Following Conditions Apply Unless Otherwise Specified: Commercial: to +85C, VCC 10%; Military: to +125C, VCC 10%

Symbol VIH VIL L I OZH I OZL VIK VH I CCL I CCH I CCZ Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(5) Input HIGH Current (I/O pins)(5) Input LOW Current (Input pins)(5) VCC = Max. VCC = Min., IIN = 18mA VCC = Max., VO = GND (3)

Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC VI = GND = 0.5V

Input LOW Current (I/O pins)(5) High Impedance Output Current (3-State Output pins) (5) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current

NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter = 55C.


 

Related products with the same datasheet
IDT54FCT162H244CT
IDT54FCT162H244ET
IDT54FCT162H244T
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT162H244ATE Fast CMOS 16-bit Buffer/line Driver
IDT54FCT162H244CT
IDT54FCT162H244CTE
IDT54FCT162H244ET
IDT54FCT162H244ETE
IDT54FCT162H244T
IDT54FCT162H244TE
IDT54FCT162H245 Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245AT Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245ATE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245CT Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245CTE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245ET Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245ETE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245T Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245TE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H272AT Fast CMOS 12-bit Synchronous Bus Exchanger
IDT54FCT162H501 Fast CMOS 18-bit Registered Transceiver

IDT72851L-10 : Dual CMOS Syncfifo(tm) Dual 256x9, Dual 512x9, Dual 1,024x9, Dual 2,048x9, Dual 4,096x9, Dual 8,192x9

IDT74FCT374AL : CMOS/BiCMOS->FCT/FCT-T Family Fast CMOS Octal D Registers (3-state)

IDT74FCT573L : CMOS/BiCMOS->FCT/FCT-T Family Fast CMOS Octal Transparent Latch

IDT7M1002S40G : 16k X 32 CMOS Dual-port Static RAM Module

72P51759L6BB8 : 1.8V MULTI-QUEUE FLOW-CONTROL DEVICES (128 QUEUES) 36 BIT WIDE CONFIGURATION

IDT70V5388S133BC : 3.3V 64/32k X 18 Synchronous Fourport Static RAM

IDT72V821L10TF8 : 3.3v Dual CMOS Syncfifo(tm)

IDT82V2048DAG : Octal E1 Short HAUL LINE Interface UNIT

IDT71V2558SA133BQI : 128K X 36 ZBT SRAM, 5 ns, PBGA119 Specifications: Memory Category: SRAM Chip ; Density: 4719 kbits ; Number of Words: 128 k ; Bits per Word: 36 bits ; Package Type: BGA, 14 X 22 MM, PLASTIC, MS-028AA, BGA-119 ; Pins: 119 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 5 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT723641L20PFI : 1K X 36 OTHER FIFO, 11 ns, PQFP120 Specifications: Memory Category: FIFO ; Density: 37 kbits ; Number of Words: 1 k ; Bits per Word: 36 bits ; Package Type: TQFP, TQFP-120 ; Pins: 120 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 11 ns ; Cycle Time: 15 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

72V3670L15PFGI : 8K X 36 OTHER FIFO, 6.5 ns, PQFP128 Specifications: Memory Category: FIFO ; Density: 295 kbits ; Number of Words: 8 k ; Bits per Word: 36 bits ; Package Type: TQFP, PLASTIC, TQFP-128 ; Pins: 128 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 6.5 ns ; Cycle Time: 10 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

Same catergory

2SC5109 : Bipolar Transistors. Vceo (V) = 10 ;; Ic (mA) = 60 ;; PC (mW) = 150 ;; Cob (pF) = 0.9 ;; Cre (pF) = 0.7 ;; .fT(Typ.) (GHz) = 5 ;; Package = S-mini ;; Application = VHF to UHF Osc.

5815 : . Designed primarily for use with high-voltage vacuum-fluorescent displays, the UCN5815A and UCN5815EP BiMOS II integrated circuits consist of eight npn Darlington source drivers with output pulldown resistors, a CMOS latch for each driver, and common STROBE, BLANKING, and ENABLE functions. BiMOS II devices have considerably better data-input rates than.

ITM-M-21-3.7 : B/w Camera Module. This is a family of products based on the most advance CMOS mixed signal technology. It integrates image array, signal processing, timing and control circuitry, all on a single chip, enabling all aspects of B/W video camera applications. It is ideal for applications requiring a small footprint, low power and low cost. Visual door phone Video conferencing.

LA5318M : Voltage Regulator, Voltage Divider For Lcds, Package : Sop. The is a variable divided voltage generator IC for multiple drive of LCD matrix. Power supply for variable bias LCD division drive to 1/19 bias available by built-in resistances). Four operational amplifiers to deliver 5 voltage outputs. Low current drain (0.35mA typ). V1, V2 output current source side variable pin. Output on/off function VREF control.

MAC4DCNT4 : Triac, Package: Dpak, Pins=3. Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Small Size Surface Mount DPAK Package Passivated Die for Reliability and Uniformity Blocking Voltage 800 V OnState Current Rating of 4.0 Amperes RMS at 108C High Immunity to dv/dt 500 V/ms at 125C.

RFP25N05 : 25a, 50v, 0.047 Ohm, N-channel Power MOSFET. The RFP25N05 N-channel power MOSFET is manufactured using the MegaFET process. This process which uses feature sizes approaching those of LSI integrated circuits, gives optimum utilization of silicon, resulting in outstanding performance. It was designed for use in applications such as switching regulators, switching converters, motor drivers, and relay.

SN74AHCT574DBLE : D-Type (3-State) Flip-Flops. ti SN74AHCT574, Octal Edge-triggered D-type Flip-flops With 3-State Outputs.

CHM2304PT : N-channel Enhancement Mode Field Effect Transistor. CHM2304PT SURFACE MOUNT N-Channel Enhancement Mode Field Effect Transistor APPLICATION * Servo motor control. * Power MOSFET gate drivers. * Other switching applications. FEATURE * Small flat package. ) * High density cell design for extremely low RDS(ON). * Rugged and reliable. * High saturation current capability. Drain-Source Voltage Gate-Source.

F931A685MAA : Solid Tantalum Electrolytic Capacitors. s Item Category Temperature Range Capacitance Tolerance Dissipation Factor (120Hz) ESR (100kHz) Performance Characteristics ~ +125C (Rated temperature 20%, 10% (at 120Hz) Refer to next page Refer to next page After 1 minute's application of rated voltage, leakage current 20C is not more than or 0.5A, whichever is greater. After 1 minute's application.

JM161B : 1 External Dimension.

ECE-A1HKSR22B : 0.22F Aluminum Capacitor Radial, Can 50V; CAP ALUM 0.22UF 50V 20% RADIAL. s: Capacitance: 0.22F ; ESR (Equivalent Series Resistance): - ; : General Purpose ; Lifetime @ Temp.: 1000 Hrs @ 85C ; Size / Dimension: 0.157" Dia (4.00mm) ; Lead Spacing: 0.197" (5.00mm) ; Surface Mount Land Size: - ; Mounting Type: Through Hole ; Package / Case: Radial,.

RS3-4812SZ : DC/DC Converters & Regulators 3W DC/DC 1kV REG 3:1 20-60Vin 12Vout. s: Manufacturer: RECOM Power ; RoHS:  Details ; Product: Isolated ; Output Power: 3 W ; Input Voltage Range: 20 V to 60 V ; Input Voltage (nominal): 48 V ; Number of Outputs: 1 ; Output Voltage (Channel 1): 12 V ; Output Current (Channel 1): 250 mA ; Isolation Voltage: 1 KV ; Package.

1-796866-6 : Through Hole Terminal Block - Headers, Plug And Socket Connectors, Interconnect Header, Male Pins, Shrouded (4 Side); TERM BLK HEADER 16POS R/A 5.08MM. s: Terminal Block Type: Header, Male Pins, Shrouded (4 Side) ; Positions Per Level: 16 ; Pitch: 0.200" (5.08mm) ; Number of Levels: 1 ; Header Orientation: 90, Right Angle ; Plug Wire Entry: - ; Termination:.

20020008-D071B01LF : Free Hanging (In-Line) Terminal Block - Headers, Plug And Socket Connectors, Interconnect Plug, Female Sockets; TERM BLOCK PLUG 7POS 3.81MM. s: Terminal Block Type: Plug, Female Sockets ; Positions Per Level: 7 ; Pitch: 0.150" (3.81mm) ; Number of Levels: 1 ; Header Orientation: - ; Plug Wire Entry: 90 ; Termination: Screw ; Wire Gauge: 16-28 AWG ; Current:.

19-123/Y2ST1D-C30/2T : DUAL COLOR LED, BRILLIANT YELLOW/PURE WHITE, 1.5 mm. s: LED Type: White, Multi-Colored ; Peak Wavelength: 591 nm (5910 Å) ; Viewing Angle: 140 degrees ; Luminous Intensity: 0.0502 to 0.0785 milliCandela ; Forward Current: 50 milliamps ; LED Package : ROHS COMPLIANT, SMD, 4 PIN.

 
0-C     D-L     M-R     S-Z