Details, datasheet, quote on part number: IDT54FCT162841BTPAB
CategoryLogic => Latches => CMOS/BiCMOS->FCT/FCT-T Family
DescriptionFast CMOS 20-bit Transparent Latch
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT162841BTPAB datasheet
Find where to buy


Features, Applications

0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage 1A (max.) VCC 5V 10% Balanced Output Drivers 24mA Reduced system switching noise Typical VOLP (Output Ground Bounce) 0.6V at VCC = 25C Available in SSOP and TSSOP packages

The FCT162841T 20-bit transparent D-type latches are built using advanced dual metal CMOS technology. These high-speed, low-power latches are ideal for temporary data storage. They can be used for implementing memory address latches, I/O ports, and bus drivers. The Output Enable (OE) and Latch Enable (LE) controls are organized to operate each device as two 10-bit latches or one 20-bit latch. Flow-through organization of signal pins simplifies layout. All inputs are designed with hysteresis for improved noise margin. The FCT162841T has balanced output drive with current limiting resistors. This offers low ground bounce, minimal undershoot, and controlled output fall timesreducing the need for external series terminating resistors. The is a plug-in replacement for the FCT16841T and ABT16841 for on-board interface applications.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Symbol Description Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Storage Temperature DC Output Current Max to +120 Unit C mA

NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXX Output and I/O terminals. 3. Outputs and I/O terminals for FCT162XXX.

Symbol CIN COUT Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. 6 8 Unit pF

NOTE: 1. This parameter is measured at characterization but not tested.

Pin Names xDx xLE x Qx Data Inputs Latch Enable Inputs (Active HIGH) Output Enable Inputs (Active LOW) 3-State Outputs Description

NOTES: H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care Z = High-Impedance 2. Output level before xLE HIGH-to-LOW transition.

Following Conditions Apply Unless Otherwise Specified: Industrial: to +85C, VCC 5.0V 10%

Symbol VIH VIL IIH Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(5) Input HIGH Current (I/O pins)(5) IIL Input LOW Current (Input pins)(5) Input LOW Current (I/O pins)(5) IOZH IOZL VIK IOS VH ICCL ICCH ICCZ High Impedance Output Current (3-State Output pins)(5) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current VCC = Max. VIN = GND or VCC = Min., IIN = 18mA VCC = Max., = GND(3) VCC = Max. VI = GND Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC Min. 80 Typ.(2) Max. mV A Unit V A

Symbol IODL IODH VOH VOL Parameter Output LOW Current Output HIGH Current Output HIGH Voltage Output LOW Voltage Test Conditions(1) VCC = 5V, VIN = VIH or VIL, = 1.5V(3) VCC = 5V, VIN = VIH or VIL, = 1.5V(3) VCC = Min IOH = 24mA VIN = VIH or VIL VCC = Min IOH = 24mA VIN = VIH or VIL Min. 2.4 Typ.(2) Max. 200 0.55 Unit mA V

NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. This test limit for this parameter = 55C.


Related products with the same datasheet
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT162841BTPF Fast CMOS 20-bit Transparent Latch
IDT54FCT162841ET Fast CMOS 20-bit Transparent Latches
IDT54FCT162841ETE Fast CMOS 20-bit Transparent Latch
IDT54FCT162952 Fast CMOS 16-bit Registered Transceiver
IDT54FCT162H244 Fast CMOS 16-bit Buffer/line Driver
IDT54FCT162H245 Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162H245AT Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162H245ATE Fast CMOS 16-bit Bidirectional Transceiver

82V1074 : Quad Programmable PCM Codec

IDT54FCT244PY : Fast CMOS Octal Buffer/line Driver

IDT54FCT825BTD : High-performance CMOS Bus Interface Registers

IDT72261L12TF : CMOS Supersync Fifoo 16,384 X 9, 32,768 X 9

IDT728985J : 256 X 256 Time Slot Interchange Digital Switch, 5.0V

IDT70V08S20PFI : High-speed 3.3V 128K x 8 Dual-port Static RAM

MK1491-09F : Clock/timing - Application Specific Integrated Circuit (ics) Clock/Frequency Synthesizer Tube 3.15 V ~ 3.45 V; IC CLK SRC AMD GEODE GX2 28-SSOP Specifications: Type: Clock/Frequency Synthesizer ; PLL: No ; Main Purpose: AMD CPU ; Input: Crystal ; Output: LVCMOS ; Number of Circuits: 1 ; Ratio - Input Output: 1 12 ; Differential - Input Output: No/No ; Frequency - Max: 66MHz ; Voltage - Supply: 3.15 V ~ 3.45 V ; Operating Temperature: 0C ~

IDTQS3VH253PAG8 : 2.5V / 3.3V 10-bit HIGH AND LOW Enable, HIGH Bandwidth BUS Switch

ICS8530-01DYLFT : LOW SKEW CLOCK DRIVER, 16 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP48 Specifications: Device Type: Clock Driver ; Package Type: Surface Mount, 7 X 7 MM, 1.40 MM HEIGHT, 0.50 MM PITCH, PLASTIC, MS-026, LQFP-48 ; Supply Voltage: 3.14 to 3.46 volts ; Skew: 75 ps ; Frequency: 500 MHz ; Operating Temperature: 0.0 to 70 C (32 to 158 F)

IDT7140LA25TF8 : 1K X 8 DUAL-PORT SRAM, 100 ns, CDIP48 Specifications: Memory Category: SRAM Chip ; Density: 8 kbits ; Number of Words: 1 k ; Bits per Word: 8 bits ; Package Type: DIP, SIDE BRAZED, DIP-48 ; Pins: 48 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 100 ns ; Operating Temperature: -40 to 85 C (-40 to 185 F)

74FCT821BP : FCT SERIES, 10-BIT DRIVER, TRUE OUTPUT, PDIP24 Specifications: Technology: CMOS ; Device Type: Line / Bus Driver ; Supply Voltage: 5V ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Package Type: DIP, PLASTIC, DIP-24 ; Pins: 24

0-C     D-L     M-R     S-Z