Details, datasheet, quote on part number: IDT54FCT162827BTE
CategoryLogic => Bus Interface => Bus Oriented Circuits
TitleBus Oriented Circuits
DescriptionFast CMOS 20-bit Buffer
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT162827BTE datasheet
Find where to buy


Features, Applications

0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage 1µA (max.) ESD > 2000V per MIL-STD-883, Method > 200V using machine model = 0) VCC 5V ±10% Balanced Output Drivers (±24mA) Reduced system switching noise Typical VOLP (Output Ground Bounce) 0.6V at VCC = 25°C Available in SSOP and TSSOP packages

The FCT162827T 20-bit buffers are built using advanced dual metal CMOS technology. These 20-bit bus drivers provide high-performance bus interface buffering for wide data/address paths or buses carrying parity. Two pair of NAND-ed output enable controls offer maximum control flexibility and are organized to operate the device as two 10-bit buffers or one 20-bit buffer. Flowthrough organization of signal pins simplifies layout. All inputs are designed with hysteresis for improved noise margin. The FCT162827T has balanced output drive with current limiting resistors. This offers low ground bounce, minimal undershoot, and controlled output fall times­reducing the need for external series terminating resistors. The is a plug-in replacement for the FCT16827T and ABT16827 for on-board interface applications.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Symbol Description Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Storage Temperature DC Output Current Max to +120 Unit °C mA

NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXX Output and I/O terminals. 3. Outputs and I/O terminals for FCT162XXX.

Symbol CIN COUT Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. 6 8 Unit pF

NOTE: 1. This parameter is measured at characterization but not tested.
Pin Names OE x xAx xYx Data Inputs 3-State Outputs Description Output Enable Inputs (Active LOW)
NOTE: H = HIGH voltage level L = LOW voltage level X = Don't care Z = High-impedance
Following Conditions Apply Unless Otherwise Specified: Industrial: to +85°C, VCC 5.0V ±10%

Symbol VIH VIL IIH IIL IOZH IOZL VIK IOS VH ICCL ICCH ICCZ Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(4) Input HIGH Current (I/O pins)(4) Input LOW Current (Input pins)(4) Input LOW Current (I/O pins)(4) High Impedance Output Current (3-State Output pins)(4) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current VCC = Max VIN = GND or VCC = Min., IIN = ­18mA VCC = Max., = GND(3) VCC = Max. VI = GND Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC Min. ­80 Typ.(2) Max. mV µA Unit V µA

Symbol IODL IODH VOH VOL Parameter Output LOW Current Output HIGH Current Output HIGH Voltage Output LOW Voltage Test Conditions(1) VCC = 5V, VIN = VIH or VIL, = 1.5V(3) VCC = 5V, VIN = VIH or VIL, = 1.5V(3) VCC = Min. VIN = VIH or VIL VCC = Min. VIN = VIH or VIL

NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC 5.0V, +25°C ambient. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. This test limit for this parameter = ­55°C.


Related products with the same datasheet
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT162827BTEB Fast CMOS 20-bit Buffer
IDT54FCT162827ET Fast CMOS 20-bit Buffers
IDT54FCT162827ETE Fast CMOS 20-bit Buffer
IDT54FCT162841 Fast CMOS 20-bit Transparent Latch
IDT54FCT162841ET Fast CMOS 20-bit Transparent Latches
IDT54FCT162841ETE Fast CMOS 20-bit Transparent Latch
IDT54FCT162952 Fast CMOS 16-bit Registered Transceiver
IDT54FCT162H244 Fast CMOS 16-bit Buffer/line Driver

IDT54FCT640AT : Fast CMOS Octal Bidirectional Transceivers

IDT7130SA20TF : High-speed 1k X 8 Dual-port Static RAM

IDT74FCT22245CTPB : Fast CMOS Octal Bidirectional Transceivers

IDT70V9389L7PRFI : High-speed 3.3V 64K X18/x16 Synchronous Pipelined Dual-port Static RAM

92HD005DX3PRGXYYX : 4-channel HD Audio Codec WITH QUAD Digital Microphone Interface

ICS84324EMLF : 375 MHz, OTHER CLOCK GENERATOR, PDSO16 Specifications: Device Type: Clock Generator ; Package Type: Surface Mount, TSSOP, 4.40 X 5 MM, 0.92 MM HEIGHT, MO-153, TSSOP-16 ; Supply Voltage: 2.38 to 2.62 volts ; Frequency: 25 MHz ; Operating Temperature: 0.0 to 70 C (32 to 158 F)

IDT2309NZ-1HDCGI : 2309 SERIES, PLL BASED CLOCK DRIVER, 8 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 Specifications: Device Type: Clock Driver ; Package Type: Surface Mount, TSSOP, TSSOP-16 ; Supply Voltage: 3 to 3.6 volts ; Skew: 250 ps ; Frequency: 133 MHz ; Operating Temperature: 0.0 to 70 C (32 to 158 F)

IDT74LVC4X374Q3 : LVC/LCX/Z SERIES, HEX 1-INPUT INVERT GATE, PDSO14 Specifications: Gate Type: NOT ; Supply Voltage: 3.3V ; Output Type: Open Drain ; Logic Family: CMOS ; Inputs: 1 ; Propagation Delay: 3.9 ns ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Pin Count: 14 ; IC Package Type: SOIC, Other, 1.27 MM PITCH, SOIC-14

72V3696L15PFG8 : IC,FIFO,2X32KX36,SYNCHRONOUS,CMOS,QFP,128PIN,PLASTIC Specifications: Memory Category: FIFO

0-C     D-L     M-R     S-Z