|Company||Nihon Kaiheiki Industry|
|Datasheet||Download M2016TNG datasheet
Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. The molded diallyl phthalate case has UL 94V-0 flammability rating. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Prominent external insulating barriers increase insulation resistance and dielectric strength. Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength.
Power Level (code W): Logic Level (code G): Logic/Power Level (code A): 30V DC for On-None-On; 30V DC for all other circuits 0.4VA maximum @ 28V AC/DC maximum (Applicable Range ~ 28V) Combines & G ratings Note: Find additional explanation of dual rating & operating range in Supplement section.
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts and case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold; 50,000 operations minimum for silver AC 25°
Actuator Clip & Mounting Frame: Body Frame: Case: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Stainless Steel Stainless steel Diallyl phthalate resin (UL94V0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; or copper or brass with gold plating
Operating Temp Range: Humidity: Vibration: Shock: 30°C through +85°C (22°F through ~ 95% humidity for 96 hours ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Actuator must be in OFF (center) position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution.
Flammability Standards: UL Recognized: UL94V0 for case All models recognized or 0.4VA maximum 28V DC maximum; UL File No. WOYR2.E44145; add "/U" to end of part number to order UL mark on switch. All models recognized or 0.4VA maximum @ 28V maximum; CSA File No. 023535-0-000; add "/C" to end of part number to order CSA mark on switch.
Small Actuators (TN Frame) G.365" (9.27mm) Wide Rocker.365" (9.27mm) Wide Paddle.450" (11.43mm) Wide Rocker.450" (11.43mm) Wide Paddle.595" (15.11mm) Wide Rocker.595" (15.11mm) Wide Paddle
G A Silver; Rated 250V AC Gold; Rated 0.4VA max @ 28V AC/DC max Gold over Silver; Rated & 0.4VA max @ 28V AC/DC maxON (ON) ON (ON) ON NONE OFF NONE OFF ON (ON) ON (ON) 01 03
Black White Red Yellow Green Blue Gray
Switches are supplied without UL & CSA marking unless specified. Specific models & ratings noted on General Specifications page.
Red.365" (9.27mm) Wide Rocker.272" (6.9mm) Wide Flat Frame SPDT ON-NONE-ON Circuit Silver Contacts with 6-Amp Rating Solder Lug Terminals
|Related products with the same datasheet|
|Some Part number from the same manufacture Nihon Kaiheiki Industry|
|M2016TNW Miniature Rockers|
|JWM11RC Internationally Approved TV Rated Rockers|
|B2RJW Process Sealed Subminiature Antistatic Toggles|
|A17KB1 Process Sealed Subminiature Rockers|
|B15EH Process Sealed Subminiature Antistatic Toggles|
|UB16NKG015C Distinctive Characteristics|
|SW3821 High Capacity Rockers|
|M2122TFG LED Tipped Actuators|
|MS12AFG Miniature Slides|
|WR11BL Environmentally Sealed Rockers|
|M2042TNA Miniature Rockers|
|JWL21BB Internationally Approved TV Rated Rockers|
|FR02FC10P-R 10mm Ultra-thin SMT DIP Rotaries|
|B18LB Process Sealed Subminiature Antistatic Toggles|
|WR13AT Environmentally Sealed Rockers|
PDMB75A6 : Device = Igbt ;; Maxisimam Operating Junction Temperature( C ) = 150 ;; Storage Temperature( C ) = -40 to +125 ;; Circuit = Half Bridge ;; Data Sheet(pdf) = _pdmb75a6.pdf ;; Outline(dxf) = Pdmb75a6.dxf ;; Remarks = ;; = ;; = ;; = ;;
LB25CGG01-H : Standard Size Pushbuttons
G3B15AB-S-XA : Ultra-miniature Process Sealed SMT Pushbuttons
UB15RKG01N-F : Distinctive Characteristics
M2112JCFW : LED Tipped Actuators
NT2520SA : Crystal Oscillator
A16KB : Process Sealed Subminiature Rockers
SCB25S15B-1B : Snap Switch Pushbuttons
SW3823D : High Capacity Rockers
EC10QS06TE12R5 : 0.72 A, 60 V, SILICON, SIGNAL DIODE Specifications: Number of Diodes: 1 ; IF: 720 mA