Details, datasheet, quote on part number: 422PP9TB
CategoryInterface and Interconnect => Line Drivers
DescriptionTwo Channel
CompanyB&B Electronics
DatasheetDownload 422PP9TB datasheet


Features, Applications

The is a port-powered two-channel to RS-422 converter. It converts TD and RD RS-232 lines to balanced RS-422 signals. The unit can be powered from the RS-232 handshake lines, DTR and RTS. If port-powering the unit, at least one of these handshake lines must be present, but can be in any state. The 422PP9TB can also be powered externally on the terminal blocks. The RS-422 driver and receiver are always enabled. To satisfy the requirements of some software packages, the RS-232 handshake lines are looped back (tied together). RTS is connected to CTS, and DTR is connected to DSR and DCD. Connections The 422PP9TB is configured to transmit both directions between an RS-232 and RS-422 system. The RS-232 side is pinned out to connect directly into the COM port on your computer or any other DTE device (Table 1). Connections to the RS-422 side of the converter are made through terminal blocks. When connecting an RS-422 system, the 422PP9TB must be connected with the proper polarity as shown in Figure 1. When no data is being sent and the driver enabled, the RS-232 line is negative and the RS-422 line TD(A) is negative with respect to TD(B).

This product designed and manufactured in USA of domestic and imported parts by

Document No. 422PP9TB4300 - pg. 2/2 Biasing Resistors The biasing resistors for the RS-422/RS-485 receiver are 4.7k Ohm resistors. These resistors are labeled R1 and R2 (See Figure 2). Refer to B&B Electronics RS-422/485 Application Note for further information on biasing.

Specifications Communication: Data Rate: Power: Dimensions: Temperature Rating:

RS-422 115.2 kbps max. Port-powered from handshake lines on the RS-232 side, to 16 VDC mA on the terminal blocks. x 1.7 cm) to 70°C

NOTE: When using an external supply, the supply should be connected only to specifically labeled power inputs (power jack, terminal block, etc.). Connecting an external power supply to the handshake lines may damage the unit. Contact technical support for more information on connecting an external power supply to the handshake lines.

Manufacturer's Name: Manufacturer's Address: B&B Electronics Manufacturing Company P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA 422PP9TB 9-Pin Port-Powered RS-422 Converter Light industrial ITE equipment EN 50082-1 (IEC 801-2, IEC 801-3, IEC EN 50081-1 (EN 55022, IEC 1000-4-2) EN ENV EN 55024


Some Part number from the same manufacture B&B Electronics
422TTL Four Channel Rs-422 to TTL Converter
485BAT3 Battery Powered Rs-232/422/485 Converter
485DRJ Port Powered Rs-232 to Rs-485 Converter
485DSS Intelligent Rs-232 to Rs-485 Converter/switch
485DTT Digital Thermometer & Thermostat With Rs-485 Interface
485FPP Rs-422/485 Fused Port Protector
485FWTW Rs-485/422 Four Wire-two Wire Converter
485HSPR Rs-232 to Rs-485 ISOlated Converter
485LP9N Port Powered Rs-232 to Rs-485 Converter
485OFS Rs-485 Node ISOlator
485OI9TB Rs-232 to Rs-485 ISOlated Converter
485OP Rs-422/485 Optically ISOlated Repeater
485OT9L Rs-232 to Rs-485 ISOlated Converter

232FLSTDB25 : Port Powered Rs-232 Fiber Modem

232PCI1A : Pci 1-port Rs-232 Serial Card W/16550a Uart

422OISPR : Two Channel ISOlated Rs-232 to Rs-422 Converter

485OP : Rs-422/485 Optically ISOlated Repeater

9PFLST : Db9 Port-powered Rs-232 Fiber Modem

SMP : Ac/phone Surge Protector

EIS-M-SC : Undefined Family Undefined Category; MEDIA CONVERTER 10/100 TO 100FX Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ESW108-ML : Undefined Family Undefined Category; 8 PORT COMPACT ETHERNET SWITCH Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

WLNN-ER-DP551 : WiFi / 802.11 Modules WLAN ETHERNET ADPT ADV ENTERPRISE SEC Specifications: Manufacturer: B&B Electronics ; Protocol Supported: 802.11 a/b/g/n ; Frequency Band: 2.4 GHz to 2.4835 GHz ; Data Rate: 11 Mbps, 54 Mbps, 65 Mbps ; Interface Type: 10/100 Ethernet, UART, RS-232/422/485, SPI, PortFlex ; Transmit Power - Max: 12.6 dBm, 15 dBm, 17 dBm ; Operating Supply

WSKIT4BE : DEV KIT SPECTRERT Specifications: Family: RF Evaluation and Development Kits, Boards ; Series: Wzzard? ; Type: Gateway ; Frequency: - ; For Use With/Related Products: SpectreRT ; Supplied Contents: 4 Boards, Cable, Router ; Online Catalog: Wzzard? Design and Development Kits

Same catergory

7ABT543APWDH : Octal Latched Transceiver With Dual Enable 3-state. 74ABT543A Octal latched transceiver with dual enable (3-State) Product Supersedes data of 1995 Apr 19 IC23 Data Handbook 1998 Sep 24 Octal latched transceiver with dual enable (3-State) Combines 74ABT245 and 74ABT373 type functions in one device 8-bit octal transceiver with D-type latch Back-to-back registers for storage Separate controls for data flow.

A6118SLW : Addressable 28-Line Decoder/driver. Integrating seven high-voltage, high-current npn Darlingtons into a monolithic power array, the ULN7003A AND ULN7003LW are designed for interfacing between TTL or CMOS logic and a variety of peripheral loads. The seven open-collector Darlington outputs are specified for 135 V minimum breakdown and 90 V minimum sustaining. Included are integral power.

CY7C63001A-SC : USB Low-Speed Peripherals. 8-bit Risc Microcontrollers (M8 Series) - Optimized From The Ground up For Usb Applications.

DS2125 : DS2125 Ultra3 Lvd/se 15-Line Scsi Terminator. The DS2125 Ultra3 LVD/SE SCSI terminator is both a low-voltage differential (LVD) and single-ended (SE) terminator. The multimode operation enables the designer to implement LVD in current products while allowing the end user SE backward compatibility with legacy devices. If the device is connected in an LVD-only bus, the DS2125 uses LVD termination.

DS96176 : DS96176 - RS-485/RS-422 Differential Bus Transceiver, Package: Mdip, Pin Nb=8.

LC895194 : Cd-rom Error Correction Lsi With On-chip Atapi (IDE) Interface. CD-ROM Error Correction LSI with On-Chip ATA-PI (IDE) Interface CD-ROM error detection and correction, ATA-PI (IDE) interface (including the register and other blocks) ATA-PI (IDE) interface Supports 16×-speed playback (with IORDY): Using 70 ns DRAMs 16.6 MB/s transfer rate: Using 70 ns DRAMs Supports the use of from M of buffer RAM. (DRAM) Allows the user.

MH88612BV-2 : Analog Subscriber Line Interfaces (SLIC). = Short Loop Slic With 2-4 Wire Conversion 600 Ohms Line Impedance ;; Package Type = N/a ;; No. Of Pins =.

PACAC : Pactive ac Termination Network.

PDIUSBH12 : PDIUSBH12; Usb 2-port Hub. Complies with the Universal Serial Bus Rev. 1.0 Complies with the ACPI, OnNOW, and USB power management The Universal Serial Bus Hub is a cost and feature optimized second generation USB Hub with 2 downstream ports and 3 embedded functions (compound hub). It is normally used in any microcontroller-based system and communicates with the system microcontroller.

SN75157 : Dual Differential Line Receiver For Rs422a And Rs423a: 2 Receivers. Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and EIA/TIA-423-B and ITU Recommendation V.10 and V.11 Operates From Single 5-V Power Supply Wide Common-Mode Voltage Range High Input Impedance TTL-Compatible Outputs High-Speed Schottky Circuitry 8-Pin Dual-In-Line Package The is a dual differential line receiver designed to meet Standards.

TDA5153 : Pre-amplifier For Hard Disk Drive (hdd) With Mr-read/inductive Write Heads.

UC5605 : 9-line Low Capacitance Scsi Active Terminator. Reverse Disconnect Complies with SCSI, SCSI-2 and SPI-2 Standards 5pF Channel Capacitance during Disconnect Hot Plugging Capability -400mA Sourcing Current for Termination +100mA Sinking Current for Active Negation 1V Dropout Voltage Regulator 100µA Supply Current in Disconnect Mode Trimmed Termination Current to 5% Trimmed Impedance to 5% Low Thermal.

UCC1776 : Quad Fet Driver. High Peak Output Current Each Output ­ 1.5A Source, 2.0A Sink Wide Operating Voltage Range to 18V Thermal Shutdown CMOS Compatible Inputs Outputs Are Active Low for Undervoltage Lockout Condition The is a four output BCDMOS buffer/driver designed to drive highly capacitive loads such as power MOSFET gates at high speeds. The device can be configured.

ULN2064 : Quad 1.5 a Darlington Switches. High-voltage, high-current Darlington arrays ULN2064B/LB through ULN2069B/LB are designed for interface between low-level logic and a variety of peripheral loads such as relays, solenoids, dc and stepper motors, magnetic print hammers, multiplexed LED and incandescent displays, heaters, and similar loads. Output off voltage ratings 50 V and 80 V are available.

XRT83L30 : Single-channel T1/E1/J1 Long-Haul, Short-haul Line Interface Unit. SINGLE-CHANNEL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR The is a fully integrated single-channel long-haul and short-haul line interface unit for or 120 and J1 110 applications. In long-haul applications the XRT83L30 accepts signals that have passed through cables from 0 feet to over 6000 feet in length and have been attenuated.

DS25CP104 : 3.125 Gbps 4x4 LVDS Crosspoint Switch with Transmit Pre-Emphasis and Receive Equalization from the PowerWise® Family The DS25CP104 is a 3.125 Gbps 4x4 LVDS crosspoint switch optimized for high-speed signal routing and switching over lossy FR-4 printed circuit board backplanes and balanced cables. Fully differential signal paths ensure exceptional signal.

FSA800 : Multimedia And USB 2.0 Hi-Speed Switch The FSA800 is a 3:1 USB accessory switch that enables USB data, stereo and mono audio, microphone, and UART data to share a common connector port. It is designed for high-speed USB 2.0 signaling. The architecture is designed to allow audio signals to swing below ground so a common USB and headphone jack can be used.

XR17V354 : High Performance Quad PCI Express UART The XR17V354¹ ((V354) is a single chip 4-channel PCI Express (PCIe) UART (Universal Asynchronous Receiver and Transmitter), optimized for higher performance and lower power. The V354 serves as a single lane PCIe bridge to 4 indepedent enhanced 16550 compatible UARTs. The V354 is compliant to PCIe 2.0 Gen 1 (2.5GT/s)..

0-C     D-L     M-R     S-Z