|Category||Interface and Interconnect => Line Drivers|
|Datasheet||Download 422PP9R datasheet
The is a port-powered, two-channel to RS-422 converter. It converts TD and RD RS-232 lines to balanced RS-422 signals. The unit is powered from the RS-232 handshake lines DTR and RTS. Only one of these lines must be present, and the unit will work regardless of whether the lines are high or low. Both the RS-422 driver and receiver are enabled at all times. To satisfy the requirements of some software, the RS-232 handshake lines are looped back (tied together). RTS is connected to CTS, and DTR is connected to DCD and DSR. Connections The 422PP9R is configured to transmit both directions between an RS-232 and RS-422 system. The RS-232 side is pinned out to connect directly into the COM port on your computer or any other DTE device (Table 1). The RS-422 side of the converter is pinned out as described in Table 2. When connecting a RS-422 system, the 422PP9R must be connected with the proper polarity as shown in Figure 1. When no data is being sent the RS-232 line is negative and the RS-422 line TD(A) is negative with respect to TD(B).This product designed and manufactured in USA of domestic and imported parts by
Document No. 422PP9R4300 - pg. 2/2 Biasing Resistors The biasing resistors for the RS-422/RS-485 receiver are 4.7k Ohm resistors. These resistors are labeled R1 and R2 (See Figure 2). Refer to B&B Electronics RS-422/485 Application Note for further information on biasing.Specifications Communication: Data Rate: Power: Dimensions: Temperature Rating:
RS-422 115.2 kbps max. Port-Powered from handshake lines on the RS-232 side. x 0.66 in) to 70°C
NOTE: When using an external supply, the supply should be connected only to specifically labeled power inputs (power jack, terminal block, etc.). Connecting an external power supply to the handshake lines may damage the unit. Contact technical support for more information on connecting an external power supply to the handshake lines.
Manufacturer's Name: Manufacturer's Address: B&B Electronics Manufacturing Company P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA 422PP9R 9-Pin Port-Powered RS-422 Converter Light industrial ITE equipment EN 50082-1 (IEC 801-2, IEC 801-3, IEC EN 50081-1 (EN 55022, IEC 1000-4-2) EN ENV EN 55024
|Some Part number from the same manufacture B&B Electronics|
|422PP9TB Two Channel|
|422TTL Four Channel Rs-422 to TTL Converter|
|485BAT3 Battery Powered Rs-232/422/485 Converter|
|485DRJ Port Powered Rs-232 to Rs-485 Converter|
|485DSS Intelligent Rs-232 to Rs-485 Converter/switch|
|485DTT Digital Thermometer & Thermostat With Rs-485 Interface|
|485FPP Rs-422/485 Fused Port Protector|
|485FWTW Rs-485/422 Four Wire-two Wire Converter|
|485HSPR Rs-232 to Rs-485 ISOlated Converter|
|485LP9N Port Powered Rs-232 to Rs-485 Converter|
|485OFS Rs-485 Node ISOlator|
|485OI9TB Rs-232 to Rs-485 ISOlated Converter|
|485OP Rs-422/485 Optically ISOlated Repeater|
232UDS : Rs-232 Universal Data Splitter
25FNHTBJB : Db25 Female to Terminal Black With Hood Narrow Profile Jumper Box
422LCON : Two Channel Rs-232 to Rs-422 Converter
485DSS : Intelligent Rs-232 to Rs-485 Converter/switch
MODEL1140 : Miniature Fiber Optic Modem With V.54 Diagnostics
MODEL232MAC : Bipolar->ECL 100 Family Rs-232 to Macintosh Serial Converter
ABDN-ER-DP551 : WiFi / 802.11 Modules WiFi Ethernet Bridge Dual Band Enterprise Specifications: Manufacturer: B&B Electronics ; Protocol Supported: 802.11 a/b/g/n ; Frequency Band: 2.4 GHz, 5 GHz ; Data Rate: 65 Mbps ; Interface Type: Serial ; Transmit Power - Max: 17 dBm ; Antenna Connector Type: SMA ; Operating Supply Voltage: 4.5 V to 5.5 V ; Maximum Operating Temperature: +
ABDN-SE-DP551 : WiFi / 802.11 Modules WiFi Serial Server Dual Band Enterprise B&B Electronics' AirborneM2M line of enterprise wireless Ethernet Routers and Bridges are built for networking equipment in an array of machine to machine (M2M) applications. The small compact form factor, integrated options and ease of use make it ideal for commercial enterprise environments
WLNN-SE-DP551 : MODULE 802.11B/G AIRBORNE Specifications: Family: RF Transceiver Modules ; Series: - ; Packaging : Tray ; RF Family/Standard: WiFi ; Protocol: 802.11a/b/g/n ; Modulation: - ; Frequency: 2.4GHz ~ 2.5GHz, 5.15GHz ~ 5.85GHz ; Data Rate: 65Mbps ; Power - Output: 17dBm ; Sensitivity: -92dBm ; Serial Interfa
A2927SEB : Dual Full-bridge PWM Motor Driver. PRELIMINARY INFORMATION (Subject to change without notice) September 16, 1997 The A2927SEB motor driver is designed to drive both windings of a bipolar stepper motor or bidirectionally control two dc motors. Both bridges are capable of sustaining 50 V and include internal pulse-width modulation (PWM) control of the output current 1.5 A. For PWM current.
AD2-B : Sei/rs232 Adapter. The AD2-B adapter allows the RS485-like signal of SEI devices to interface to a standard RS232 port (9-pin DB), such as those in IBM compatible PCs. The SEI (Serial Encoder Interface) bus is a simple, quick and convenient network of SEI devices interfacing a RS232 serial port. The SEI bus supports from to 15 devices on a single 6-wire telephone-type.
HT82K96E : 8-Bit Usb Multimedia Keyboard Encoder OTP MCU This Device is an 8-bit High Performance Risc-like Microcontroller Designed For Usb Product Applications. It is Particularly Suitable For Use in Products Such as Mice, Keyboards And Joystick. A Halt Feature is Included to Reduce Power Consumption. Operating Voltage:fSYS=6M/12MHz: 4.4V~5.5V Low Voltage Reset.
IMP5111 : 9-line Scsi Terminator, 35mhz Channel Bandwidth. Ultra-Fast response for Fast-20 SCSI applications 35MHz channel bandwidth 3.3V operation Less than 3pF output capacitance Sleep-mode current less than 275µA Thermally self limiting No external compensation capacitors Implements or 16-bit (wide) applications Compatible with active negation drivers (60mA/channel) Compatible with passive and active terminations.
LB1889 : 3-phase Brushless Motor Driver For VTR Capstans. . 3-phase full-wave current linear drive system. Torque ripple correction circuit built in (variable ratio). compensation Current limiting circuit built in/with control characteristic switch. gain Output stage upper/lower oversaturation prevention circuit in (no external capacitor required). built FG amplifier built in. Thermal shutdown circuit built.
LC75742W : . The LC75742E and LC75742W are 1/2 duty VFD drivers that can be used for electronic tuning frequency display and other applications under the control of a microcontroller. These products can directly drive VFDs with to 82 segments. It also includes a key scan circuit and can support input from to 30 keys and can thus reduce the number of lines to the front.
LTC1543 : LTC1543, 3-Driver X 3-Receiver For Data/clock Signals, SSOP-28. Software-Selectable Transceiver Supports: V.36, X.21 TUV/Detecon Inc. Certified NET1 and NET2 Compliant (Test Report No. NET2/102201/97) TBR2 Compliant (Test Report No. CTR2/022701/98) Software-Selectable Cable Termination Using the LTC1344A Complete DTE or DCE Port with LTC1544, LTC1344A Operates from Single 5V Supply The a 3-driver/3-receiver multiprotocol.
LTC488 : LTC488, Low Power Quad Line Receiver, 75173/26LS32 Pinout. Low Power: ICC = 7mA Typ Designed for or RS422 Applications Single 5V Supply to 12V Bus Common Mode Range Permits ±7V Ground Difference Between Devices on the Bus 60mV Typical Input Hysteresis Receiver Maintains High Impedance in Three-State or with the Power Off 28ns Typical Receiver Propagation Delay Pin Compatible with the SN75173 (LTC488) Pin Compatible.
MAX3430 : MAX3430 ±80V Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver.
PACS1284-02QR : P/active Ieee 1284 Ecp/epp Termination Network.
SN75115D : Non-Standard Line Circuits. ti SN75115, Dual Differential Line Receiver.
SN75LVDM977DGG : ti SN75LVDM977, 9-Channel Lvd-scsi Transceiver. 9 Channels for the Data and Control Paths of the Small Computer Systems Interface (SCSI) Supports Single-Ended and Low-Voltage Differential (LVD) SCSI CMOS Input Levels ('LVDM976) or TTL Input Levels ('LVDM977) Available Includes DIFFSENS Comparators on CDE0 Single-Ended Receivers Include Noise Pulse Rejection Circuitry Packaged in Thin Shrink Small-Outline.
SP507 : Multi-protocol Transceivers. No. Of TX = 7 ;; No. Of RX = 7 ;; Data Rate (Mbps) = 20 ;; Supply Voltage (V) = 5 ;; Typ. Icc Current (mA) = 65(V.28) ;; Int. Chrg. Pump = Yes ;; Supported Protocols = RS232/RS422, RS449 EIA530, EIA530A V.10, V.11, V.28, V.35 X.21 ;; Tri-state Ability Dte/dce = 4Tx/4Rx ;; = ;; Esd (HBM) = 2KV ;; Package = 80 Pin MQFP.
SP5502 : 1.3ghz I2c Bus 4-address Synthesiser. Supersedes version in April 1994 Consumer IC Handbook, - 5.0 January 1997 The is a single-chip frequency synthesiser designed for TV tuning systems. Control data is entered in the standard I2C BUS format. The SP5502 has four programmable I2C BUS addresses, which allows two or more synthesisers to be used in a system. The device is available in two variants:.
UHP112 : PCI to USB. Provides a Single-chip Pci-to-universal Serial Bus (USB) Solution..
LMH0384 : 3 Gbps HD/SD SDI Extended Reach And Configurable Adaptive Cable Equalizer The LMH0384 3 Gbps HD/SD SDI Extended Reach and Configurable Adaptive Cable Equalizer is designed to equalize data transmitted over cable (or any media with similar dispersive loss characteristics). The equalizer operates over a wide range of data rates from 143 Mbps to 2.97 Gbps.