Details, datasheet, quote on part number: 422OPINB
CategoryCommunication => Fiber Optics
DescriptionIndustrial ISOlated Rs-232 to Rs-422 Converter W/sd Control
CompanyB&B Electronics
DatasheetDownload 422OPINB datasheet


Features, Applications

Description: The 422OPINB converts unbalanced, full-duplex RS-232 signals to balanced, full or half-duplex or RS-485 signals. The following signals are supported: TD on pin RD on pin 3, RTS on pin 4, and CTS on pin & RD can be configured as DTE or DCE with jumpers & JP2. Specifications: Signals Supported: TD, RD, RTS, & CTS Dimensions: Approximately x 0.68" Data Rate: to 19.2K baud Connectors: RS-232: DB25S (female) and Terminal Blocks RS-422/485: Terminal Blocks Isolation: 2500VAC optical isolation of data signals and ground Power Requirements: RS-232 Side: From at 40mA maximum. Apply at +12VDC and GND. RS-422/485 Side: From at 160mA maximum. Apply at I+12VDC and IGND. Configuration: In RS-485 mode, the driver enable can either be controlled with the RTS line from the RS-232 port or with an automatic circuit triggered by the transmission of data. We refer to these as RTS control and SD (send data) control. They are jumper selectable with jumper JP5. In order for jumper JP5 to have any effect, jumper JP3 must be in the 485 position. When jumper is in the 485 position, the receiver will be disabled during the transmit of data. The other option is to put jumper JP4 in the 422 position enabling the receiver all the time. In RTS mode, the RS-485 driver is enabled when the RTS handshaking line is asserted by your software. You must then disassert RTS in order to turn the RS-485 driver off again. In SD mode, the RS-485 driver is enabled whenever data is transmitted on the RS-232 TD line and disabled approximately one character length after the end of transmission (factory default is set for 9600 baud). If time-out errors occur, the baud rate time-out may need adjustment using the component values in Table & R41 are in parallel with each other. & C10 are also in parallel. If the value or C9 changes from the factory default, you must remove that component from the board before adding In RS-422 mode, jumpers & JP4 should be in the 422 position and JP5 has no effect. In 422 mode the driver and receiver will always be enable for full-duplex communications. There are 4 two-color LEDs for monitoring the supported signals (red = neg. voltage, green = pos. voltage). The board layout has an option for termination resistors (approx. 120 ohm): R9 for the 422/485 RD lines, and R31 for the 422 CTS lines. The RS-422 Standard recommends 24AWG copper conductor, twisted-pair telephone cable with a shunt capacitance of 16pf per foot to 4000 feet. The 232 and 485 power sources must be isolated in order to keep the optical isolation. Power for the 232 side will be connected at +12VDC and GND. The 485 power connects at I+12VDC and IGND. Connect the 422/485 signals TB2 as follows: 2-WIRE MODE 422OPINB: 485 Device: TD(A) & RD(A) (A) or TD(B) & RD(B) (B) or If used: RTS(A) & CTS(A) (A) or RTS(B) & CTS(B) (B) or 4-WIRE MODE 422OPINB: 422/485 Device: TD(A) Receive Data (A) or TD(B) Receive Data (B) or RD(A) --------Transmit Data (A) or RD(B) Transmit Data (B) or If used: RTS(A) Clear To Send (A) or RTS(B) Clear To Send (B) or CTS(A) Request To Send (A) or CTS(B) Request To Send (B) or Table 1. Baud Rate Time-out Replacement Values. Baud Rate Time (ms) Resistor 100K 56K Capacitor (µFd) C9.

This product designed and manufactured in USA of domestic and imported parts by


Some Part number from the same manufacture B&B Electronics
422PP9R Two Channel
422TTL Four Channel Rs-422 to TTL Converter
485BAT3 Battery Powered Rs-232/422/485 Converter
485DRJ Port Powered Rs-232 to Rs-485 Converter
485DSS Intelligent Rs-232 to Rs-485 Converter/switch
485DTT Digital Thermometer & Thermostat With Rs-485 Interface
485FPP Rs-422/485 Fused Port Protector
485FWTW Rs-485/422 Four Wire-two Wire Converter
485HSPR Rs-232 to Rs-485 ISOlated Converter
485LP9N Port Powered Rs-232 to Rs-485 Converter
485OFS Rs-485 Node ISOlator
485OI9TB Rs-232 to Rs-485 ISOlated Converter

422CON : Two Channel Rs-232 to Rs-422 Converter

BB-333 : Regulator Controller Universal Power Supply

MODEL485OPIN : Rs-485 to Rs-485 Optical ISOlator Repeater

MODEL485RPTR : Rs-422/485 Line Repeater With Surge Suppression

MESR902T : Undefined Family Undefined Category; MODBUS ETHERNET TO SERIAL SERVER Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ZXT24-RM : Undefined Family Undefined Category; ZLINX 2.4GHZ WIRELESS RADIO MODM Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ABDN-ER-IN5018 : WiFi / 802.11 Modules WiFi Ethernet Bridge Dual Band IND, POE Specifications: Manufacturer: B&B Electronics ; Protocol Supported: 802.11 a/b/g/n ; Frequency Band: 2.4 GHz, 5 GHz ; Data Rate: 65 Mbps ; Interface Type: Serial ; Transmit Power - Max: 17 dBm ; Antenna Connector Type: SMA ; Operating Supply Voltage: 4.5 V to 5.5 V ; Maximum Operating Temperature: +

WSKIT4BE : DEV KIT SPECTRERT Specifications: Family: RF Evaluation and Development Kits, Boards ; Series: Wzzard? ; Type: Gateway ; Frequency: - ; For Use With/Related Products: SpectreRT ; Supplied Contents: 4 Boards, Cable, Router ; Online Catalog: Wzzard? Design and Development Kits

Same catergory

AT24C08SC : Smart Card/Secure Card. 2-wire Serial EePROM Smart Card Modules 8k (1024 X 8).

BU8761KV : . is a PCM CODEC IC developed for digital mobile phones. This IC incorporates many analog I/O functions such as 14bit precision linear µ / A-LAW codec, two systems of microphone, amplifiers for receiver and earphone, and data signal I/O circuit. Tone generator that can output maximum 3 chord is incorporated. 1) +3V single power supply. 2) 14bit precision.

CY7C924ADX-AC : Backplane PHYs. . Second-generation HOTLink® technology Fibre Channel and ESCON®-compliant 8B/10B encoder/decoder or 12-bit pre-encoded data path (raw mode) or 10-bit encoded data transport (using 8B/10B coding) Parity check/generate Synchronous or asynchronous TTL parallel interface UTOPIA compatible host bus interface Embedded/Bypassable 256-character synchronous FIFOs.

DS2188 : -.

GP2021 : Correlators. = 12 Channel GPS Correlator ;; Package Type = MQFP ;; No. Of Pins = 80.

GTL2010PWDH : 10-bit GTL Processor Voltage Clamp. Direct interface with TTL level 6.5 ON-state connection between port Sn and Dn The is a high speed 10-bit voltage clamp. The low ON-state resistance of the clamp allows connections to be made with minimal propagation delay. The device is organized as one 10-bit voltage clamp. When D is low, the clamp is in the ON­state and a low resistance connection.

L7556 : PCM Line Card->Line Interface. Low-power Slic With Battery Switch (Not Recommended For New Designs).

LM4540 : PCM Line Card->Codec. ac '97 Codec With Stereo National 3d Sound. The is an audio codec for PC systems which performs the analog-intensive function of the Analog Codec '97 Rev 1.03 architecture. Using 18-Bit A/D and D/A converters, the LM4540 provides 90dB of dynamic range. The LM4540 was designed specifically to provide a high quality audio path and provide all analog functionality a PC audio system. It full duplex.

MF1157V-2 : Filter For E-gsm Mobile Telephone. This SAW filter for the transmitting RF circuit of E-GSM mobile communication equipment operating at 880 MHz ~ 915 MHz. 1. SMD package insures small size, lightweight. 2. Adjustment free. 3. Low insertion loss and high stop band attenuation. 4. Wide and sharp passband characteristics. 5. High stability and reliability. 6. Designed for reflow solderings.

MODEL422RMCON : Optically ISOlated Rs-232 to Rs-422/rs-485 Rack Mount or Panel Mount Converter.

MODELSS1 : Protocol Controllers. Ethernet (10base-t, 10 Base-2) to Serial Converter.

SNC588 : Two Channel Direct Drive Speech Controller.

ST5092 : 2.7v Supply 14-bit Linear Codec With High-performance Audio Front-end.

STK88C4050 : ROM-less Adpcm Voice Controller.. * Operating voltage 5.5V. * Maximum CPU operating frequency 2.7V. * Provide X'tal or RC oscillator. Both can run at high speed or slow speed(low power). RC oscillator can detect internal or external resister automatically. * I/O port. 24 I/O pins. of 24 pins with wake up function. * Five 12-bit timers. * Four channels for voice or melody processing.

TC9228AP : High Speed PLL With Built-in Prescaler.

TD6380P : Frequency Synthesizer For Tv/catv.

TH71072 : 315/433 MHZ Ask Transmitter/lo Source.

XRT73LC04A : 4-Channel DS3/E3/STS-1 Line Interface Unit. The 4-Channel, DS3/E3/STS-1 Line Interface Unit is a low power CMOS version of the XRT73L04A and consists of four independent line transmitters and receivers integrated on a single chip designed for E3 or SONET STS-1 applications. Each channel of the XRT73LC04A can be configured to support the E3 (34.368 Mbps), DS3 (44.736 Mbps) or the SONET STS-1 (51.84.

ATR0635 : ANTARIS™4 Single-chip GPS Receiver SuperSense™.

TJA1080 : FlexRay transceiver General The TJA1080 is a FlexRay transceiver, which is compatible with the FlexRay electrical physical layer V2.1 Rev. A (see Ref. 1). It is primarily intended for communication systems from 1 Mbit/s to 10 Mbit/s, and provides an advanced interface between the protocol controller and the physical bus in a FlexRay network. The TJA1080.

0-C     D-L     M-R     S-Z