Details, datasheet, quote on part number: 422LPCON
CategoryInterface and Interconnect => Line Drivers
DescriptionTwo Channel
CompanyB&B Electronics
DatasheetDownload 422LPCON datasheet


Features, Applications

This to RS-422 converter converts unbalanced RS-232 signals to balanced RS-422 signals. The power used for this converter is derived from the transmit data line (pin 2) and the handshake control lines (pins and 20). The converter can derive power from these lines when they are in the positive or negative voltage state. This permits the converter to be used in applications without any regard to software control of the handshake lines. If no handshake lines are available and all power must be derived from the transmit data line, the converter can drive limited cable lengths. A guide for this condition would be to drive only several hundred feet of transmission line and not to terminate the transmission line with a resistor of less than 1000 ohms. When more handshake lines are available longer lengths of cable can be driven. This converter has been tested at 115.2k baud with 4000 feet of cable. For applications where handshake lines are not available and long cable runs are involved, an external power supply can be connected to the terminal blocks on the RS-422 side of the converter marked "+12V" and "GND". NOTE: When using an external supply, the supply should be connected only to specifically labeled power inputs (power jack, terminal block, etc.). Connecting an external power supply to the handshake lines may damage the unit. Contact technical support for more information on connecting an external power supply to the handshake lines. The RS-232 port uses a male DB25 type of connector with pins 2 (TD input) and 3 RD(RD output) supported. Signal Ground (pin 7) is connected through to the RS-422 side on the terminal block marked "GND". Interconnection of the converter with another RS-422 device: 2. 3. The polarity of the two RS-422 lines must be correct. With no data being sent, the RS-232 line should be negative and the RS422 "A" terminal should be negative with respect to the "B" terminal. The wire recommended in the RS-422 Standard is number 24 AWG copper conductor, twisted-pair telephone cable with a shunt capacitance of 16 per foot. For long runs and/or high data rates, it is recommended that the wires be terminated with a resistor at the receive end. The twisted pair usually used has an impedance of about 100 ohms, therefore a 100 ohm resistor is normally used for the termination. The RS-422 side of the converter requires more power as the transmission line is increased and as the termination resistor value is reduced, therefore it may be necessary to use a termination resistor that is larger than 100 ohms. The RS-422 driver has the ability to drive ten RS-422 receivers connected in parallel. A system of multiple receivers may require some experimentation with location and size of termination resistors, line lengths, grounding, etc.

Manufacturer's Name: Manufacturer's Address: B&B Electronics Manufacturing Company P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA 422LPCON Port-Powered 2-Channel RS-422 Converter Light industrial ITE equipment EN 50082-1 (IEC 801-2, IEC 801-3, IEC EN 50081-1 (EN 55022, IEC 1000-4-2) EN ENV EN 55024

This product designed and manufactured in USA of domestic and imported parts by


Some Part number from the same manufacture B&B Electronics
422LPCOR Two Channel
422NOIC Two Channel ISOlated Rs-232 to Rs-422 Converter
422OP4 Four-channel Rs-422 Optical ISOlator
422OPINA Industrial ISOlated Rs-232 to Rs-422 Converter
422OPINB Industrial ISOlated Rs-232 to Rs-422 Converter W/sd Control
422PP9R Two Channel
422TTL Four Channel Rs-422 to TTL Converter
485BAT3 Battery Powered Rs-232/422/485 Converter
485DRJ Port Powered Rs-232 to Rs-485 Converter
485DSS Intelligent Rs-232 to Rs-485 Converter/switch
485DTT Digital Thermometer & Thermostat With Rs-485 Interface
485FPP Rs-422/485 Fused Port Protector
485FWTW Rs-485/422 Four Wire-two Wire Converter
485HSPR Rs-232 to Rs-485 ISOlated Converter
485LP9N Port Powered Rs-232 to Rs-485 Converter

232D23R2395 : Male to Female Pin 2 to 3 Reverser

25M6TBJB : 25-pin Male to Terminal Block Jumper Box

MODEL9MHTBJB : 9-pin Hooded Jumper Box 9-pin Hooded Jumper Box

MODELS2010/2011 : Now Asynchronous Devices CAN Access Synchronous Modems & Digital Networks

EIR-M-SC : Undefined Family Undefined Category; MEDIA CONVERTER DIN MOUNT Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

485USB9F-2W : Undefined Family Undefined Category; MINI CONVERTER USB TO RS-485 Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

3PCIU2 : Undefined Family Undefined Category; 2PORT MIPORT UNIVERSAL PCI CARD Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

APMN-Q551 : WiFi / 802.11 Modules WiFi Access Point Dual Band Module Specifications: Manufacturer: B&B Electronics ; Protocol Supported: 802.11 a/b/g/n ; Frequency Band: 2.4 GHz to 2.4835 GHz ; Data Rate: 11 Mbps, 54 Mbps, 65 Mbps ; Interface Type: 10/100 Ethernet, UART, RS-232/422/485, SPI, PortFlex ; Transmit Power - Max: 12.6 dBm, 15 dBm, 17 dBm ; Operating Supply

Same catergory

485FPP : Rs-422/485 Fused Port Protector. The 485FPP provides surge suppression for ports with or RS-485 signal levels. In addition to surge suppression, fast-acting fuses are used to protect the device against transient voltages too large or long in duration for the device to suppress. The 485FPP was designed as a disposable device. Once a fuse is blown, the unit should be replaced. The 485FPP.

DS90CR486 : Channel Link. DS90CR486 - Deserializer, Package: Tqfp, Pin Nb=100. The DS90CR486 receiver converts eight Low Voltage Differential Signaling (LVDS) data streams back into 48 bits of LVCMOS/LVTTL data. Using a 133MHz clock, the data throughput 6.384Gbit/s (798Mbytes/s). The multiplexing of data lines provides a substantial cable reduction. Long distance parallel single-ended buses typically require a ground wire per active.

GTLP2T152 : 2-Bit Lvttl/gtlp Transceiver. The a 2-bit transceiver that provides LVTTLto-GTLP signal level translation. Data directional control is handled with a transmit/receive pin. High-speed backplane operation is a direct result of GTLP's reduced output swing (<1V), reduced input threshold levels and output edge rate control. The edge rate control minimizes bus-settling time. GTLP is a Fairchild.

LB1895D : 3-phase Drushless Motor Drive For Cd-rom Spindle Motor. 1895D 3-Phase Brushless Motor Driver for CD-ROM Spindle Motors The LB1895 and LB1895D are 3-phase brushless motor drivers for use in CD-ROM spindle motors. . Current linear drive. V-type control amplifier built in. Because the power supply for the bias circuit on the upper. output side is separate, output with low saturation can be attained by boosting.

LB1980 : 3-phase Brushless Motor Driver For VCR Capstan Motors.

LPC47B27X : 100 Pin Enhanced Super I/o Controller With LPC Interface For Consumer Applications.

MIC58P01 : Latched/Addressable. MIC58P01 8-Bit Parallel-input Protected Latched Driver.

MM88C30 : Dual Differential Line Driver. MM88C29 MM88C30 Quad Single-Ended Line Driver Dual Differential Line Driver The is a dual differential line driver that also performs the dual four-input NAND or dual four-input AND function. The absence of a clamp diode to VCC in the input protection circuitry of the MM88C30 allows a CMOS user to interface systems operating at different voltage levels.

SN75138D : Non-Standard Line Circuits. ti SN75138, Quadruple Bus Transceiver. Single 5-V Supply High-Input-Impedance, High-Threshold Receivers Common Driver Strobe TTL-Compatible Driver and Strobe Inputs With Clamp Diodes High-Speed Operation 100-mA Open-Collector Driver Outputs Four Independent Channels TTL-Compatible Receiver Output The SN55138 and SN75138 quadruple bus transceivers are designed for two-way data communication.

SN75LBC771DW : Standard Line Circuits. ti SN75LBC771, GeoPort(TM) Transceiver. Supports a 9-Pin GeoPortTM Host Interface Standard for the Intelligent Network Port Designed to Operate to 4-Mbit/s Full Duplex 5 V Supply Operation Provides 6 kV ESD Protection Has Driver Short-Circuit Protection Includes Failsafe Mechanism for Open Inputs Is Backward Compatible with AppleTalkTM and LocalTalkTM Combines Multiple Components into a Single.

TB5D2HD : ti TB5D2H, 5V Quad Pecl Driver. Functional Replacements for the Agere BDG1A, BPNGA and BDGLA Pin-Equivalent to the General-Trade 26LS31 Device 2.0 ns Maximum Propagation Delays 0.15 ns Output Skew Typical Between ± Pairs Capable of Driving 50- Loads or 3.3-V Supply Operation TB5D1M Includes Surge Protection on Differential Outputs TB5D2H No Line Loading When VCC = 0 Third State Output.

TPIC44L01 : 4-channel Serial And Parallel Low-side Pre-FET Driver. Pre-FET Driver Devices Are Cascadable Internal 55-V Inductive Load Clamp and VGS Protection Clamp for External Power FETs Independent Shorted-Load/Short-toBattery Fault Detection on All Drain Terminals Independent OFF-State Open-Load Fault Sense Over-Battery-Voltage Lockout Protection and Fault Reporting Under-Battery Voltage Lockout Protection for the TPIC44L01.

W83L950D : Keyboard Controller. = Isa/lpc I/f Kbc, Flash Type, 8 ADC, 2DAC, 2PWM, 2 Master/slave Smbus, 3 PS2 I/F, 8X16 Matrix Keyboard; For Notebook KBC ;; Package = LQFP 80.

ADUM1410 : Quad-Channel Unidirectional Digital Isolator The ADuM1310 and ADuM1410 are unidirectional triple- and quad-channel isolators based on Analog Devices’ iCoupler® technology. Combining high speed CMOS and monolithic core-less transformer technology, these isolation components provide outstanding performance characteristics superior to alternatives such.

ADUM3160 : Full/Low Speed USB Digital Isolator The ADuM31601 is a USB port isolator, based on Analog Devices, Inc., iCoupler® technology. Combining high speed CMOS and monolithic air core transformer technology, this isolation component provides outstanding performance characteristics and is easily integrated with low and full speed USB-compatible peripheral devices.

DS80PCI800 : PRODUCT BRIEF 2.5 Gbps / 5.0 Gbps / 8.0 Gbps 8 Channel PCI Express Repeater With Equalization And De-Emphasis The DS80PCI800 is a low power, 8 channel repeater with 4-stage input equalization, and output de-emphasis driver to enhance the reach of PCI express serial links in board-to-board or cable interconnects. Ideal for higher density x8 and x16 PCI express.

0-C     D-L     M-R     S-Z