Details, datasheet, quote on part number: 422LP9N
CategoryInterface and Interconnect => Line Drivers
DescriptionTwo Channel
CompanyB&B Electronics
DatasheetDownload 422LP9N datasheet


Features, Applications

The is a port-powered two-channel to RS-422 converter. It converts TD and RD RS-232 lines to balanced RS-422 signals. The unit is powered from the RS-232 handshake lines DTR and RTS. One of these handshake lines must be asserted (high) in order to power the unit (See Table 1). The RS-422 driver is enabled when RTS is asserted. Therefore, RTS must be asserted in order to transmit data. The RS422 receiver is always enabled. If DTR is always asserted and the RTS is used to control the driver, the 422LP9N can be used RS-485 4-wire converter. To insure reception, it is recommended that DTR is asserted. In order to maximize the amount of power available to the RS-422 driver, the RS-232 handshake lines are not looped back (tied together). As a result the following handshake lines will appear as disasserted (low): CTS, DCD, and DSR. Care should be taken to insure that any software being used doesn't require any of these handshake lines be asserted. If existing software requires any of the handshake lines to be asserted, you can loop back the required handshake lines in your cable.

Table 1 DTR Functions Possible (when port-powering unit) State
Low High Low High none Receive Transmit, Receive Transmit, Receive

* NOTE: Low = disasserted and High = asserted Connections The 422LP9N can be connected in three different types of systems: RS-422 (Figure 1), four-wire RS-485 (Figure 1), and two-wire RS-485 (Figure 2). Regardless of the system, the 422LP9N must be connected with the proper polarity. With no data is being sent and the driver enabled, the RS-232 line should be negative and the TD(A) should be negative with respect to TD(B). Proper operation of any RS-422 system requires the presence of a signal return path between the signal grounds of the equipment at each end of an interconnection. This circuit reference may be established by a third conductor connecting the common leads of devices, or it may be provided by connections in each equipment to an earth reference. When the circuit reference is provided by a third conductor, the connection between the signal grounds and the third conductor should contain some resistance (e.g. 100 ohms) to limit circulating currents when other ground connections are provided for safety.

This product designed and manufactured in USA of domestic and imported parts by
Transmit Data A Transmit Data B Receive Data A Receive Data B Signal Ground

Biasing Resistors The biasing resistors for the RS-422/RS-485 receiver are 4.7K Ohm resistors. These resistors are labeled R1 and R6 (See Figure 3). Refer to B&B Electronics RS-422/485 Application Note for further information on biasing. Figure 3

Specifications Data Rate: 115.2K Baud max. Power: Port-Powered from RTS and DTR. NOTE: If external power is required, apply power to DTR (4) and SG (5). Source must supply greater than 6VDC and current limited to 40mA

NOTE: When using an external supply, the supply should be connected only to specifically labeled power inputs (power jack, terminal block, etc.). Connecting an external power supply to the handshake lines may damage the unit. Contact technical support for more information on connecting an external power supply to the handshake lines.

Manufacturer's Name: Manufacturer's Address: B&B Electronics Manufacturing Company P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA 422LP9N 9-Pin Port-Powered RS-422 Converter Light industrial ITE equipment EN 50082-1 (IEC 801-2, IEC 801-3, IEC EN 50081-1 (EN 55022, IEC 1000-4-2) EN ENV EN 55024


Some Part number from the same manufacture B&B Electronics
422LP9R Two Channel
422NOIC Two Channel ISOlated Rs-232 to Rs-422 Converter
422OP4 Four-channel Rs-422 Optical ISOlator
422OPINA Industrial ISOlated Rs-232 to Rs-422 Converter
422OPINB Industrial ISOlated Rs-232 to Rs-422 Converter W/sd Control
422PP9R Two Channel
422TTL Four Channel Rs-422 to TTL Converter
485BAT3 Battery Powered Rs-232/422/485 Converter
485DRJ Port Powered Rs-232 to Rs-485 Converter
485DSS Intelligent Rs-232 to Rs-485 Converter/switch
485DTT Digital Thermometer & Thermostat With Rs-485 Interface
485FPP Rs-422/485 Fused Port Protector
485FWTW Rs-485/422 Four Wire-two Wire Converter
485HSPR Rs-232 to Rs-485 ISOlated Converter

232FLST : Port Powered Rs-232 Fiber Modem

25MNHTBJB : Db25 Male to Terminal Block With Hood Narrow Profile Jumper Box

422NOICR : Two Channel ISOlated Rs-232 to Rs-422 Converter

485RPTR : Rs-485 Repeater

95860-4 : Bipolar->AS Family Pci 4-port Rs-232 Controller With Db25m Cables

ATRWDT : Watchdog Isa Watchdog Timer With Reset Pin Connector

MODEL232NM9 : Serial Cable For PC File Transfer

SCP311T-DFTB3 : Undefined Family Undefined Category; SERIAL CONVERTER PANEL MOUNT Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

RTLTE-310-W-VZ : LTE CELL ROUTER 2ETN 2SIM WIFI Specifications: Family: Gateways, Routers ; Series: * ; Online Catalog: Spectre? RTLTE-300-x Series Routers

Same catergory

440MX : Intel 440MX Chipset Electrical And Thermal addendum. Processor Host Bus Support Optimized for the Intel® Pentium® II and mobile CeleronTM processors at 66 MHz GTL+ Bus Driver Technology System Timer based on 82C54 Real Time Clock w/ 256 Bytes Battery-backed RAM X-bus Support for SIO, KBCX and Flash Integrated DRAM Support 256 MB using 16-/64/128-Mb Technology Standard and Registered SDRAM (Synchronous).

74LVTH32245G : Low Voltage 32-bit Transceiver With 3-state Outputs. The LVT32245 and LVTH32245 contain thirty-two noninverting bidirectional buffers with 3-STATE outputs and are intended for bus oriented applications. The devices are byte controlled. Each byte has separate control inputs which can be shorted together for full 32-bit operation. The T/R inputs determine the direction of data flow through the device. The OE inputs.

82801DB : Intel 82801DB I/o Controller Hub 4 (ICH4). Information in this document is provided in connection with Intel® products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied.

AD9801 : 10-Bit, 18 MSPS 1-Channel CCD Processor For Digital Still Camera And Video Conferencing Applications.

BT16899DGG : 18-bit Latched Transceiver With 16-bit Parity Generator/checker 3-state.

DP8459 : All-code Data Synchronizer (obsolete). The DP8459 Data Synchronizer is an integrated phase locked loop circuit which has been designed for application in magnetic hard disk, flexible (floppy) disk, optical disk, and tape drive memory systems for data re-synchronization and clock recovery with any standard recording code, operating to 25 Mb/s. The DP8459 is provided a 28-pin PCC package.

EM83807 : All-in-one Plug & Play 3-button Serial Mouse Controller. EM83807 ALL-IN-ONE PLUG & PLAY 3-BUTTON SERIAL MOUSE CONTROLLER The EM83807 Mouse Controller is specially designed to control serial mouse device. This single chip can interface three key-switches and 4 X-Y photo-couples directly to RS-232C. Include PnP software scrolling function Using 50k ±1% resistor for RC oscillation. Compatible with Microsoft.

LX5120 : Terminator. Ultra 27-line Scsi Terminator. The LX5120 UltraMAXTM terminator represents next-generation technology for SCSI termination applications. The low-voltage BiCMOS architecture employed in its design offers superior performance to older passive and active techniques. Linfinity's architecture employs high-speed adaptive elements for each channel, providing the fastest response possible.

NJU3718 : 20 Bit Serial to Parallel Converter.

PRN102 : Dual Thevenin Termination Network.

SN65LBC176A : Differential Bus Transceivers. High-Speed Low-Power LinBiCMOS Circuitry Designed for Signaling Rates to 30 Mbps Bus-Pin ESD Protection Exceeds 12 kV HBM Compatible With ANSI Standard TIA/EIA-485-A and ISO 8482:1987(E) Low Skew Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments Very Low Disabled Supply-Current Requirements. 700 µA Maximum Common Mode Voltage.

SN75108A : Ttl-compatible Dual Line Receiver, Totem Pole Outputs: 2 Receivers. High Speed Standard Supply Voltage Dual Channels High Common-Mode Rejection Ratio High Input Impedance High Input Sensitivity Differential Common-Mode Input Voltage Range 3 V Strobe Inputs for Receiver Selection Gate Inputs for Logic Versatility TTL Drive Capability High dc Noise Margin Totem-Pole Outputs B Version Has Diode-Protected Input for Power-Off.

HT82M32A : 3/5-Key 3D PS/2 Optical Mouse Controller The HT82M32A/HT82M32B are designed as 2D, 3D 3/5-key PS/2 optical mouse controller. These have serial interface to access the PixArt sensor PAN101, PAN301, PAN3101 or the same compatible series sensor. Refer to the datasheets for detailed register s of the PixArt sensors. Operating voltage: 4.0V~5.5V Microsoft.

TPD12S015 : HDMI Companion Chip With Step-up Converter, I2C Level Shifter, And High-speed ESD Clamps Product Reviews BETAOverall Rating Add Your Review No Reviews Yet. Add Your Review The TPD12S015 is an integrated HDMI ESD solution. The device pin mapping matches the HDMI Type C connector with four differential pairs. This device offers eight low-capacitance ESD clamps,.

73S8010R : Low-Cost Smart Card Interface The 73S8010R is a single smart card interface IC, compliant to the electrical requirements of ISO 7816-3 and EMV 4.0 electrical s. It implements an I˛C bus control, making it particulary suitable for applications that require several card interfaces. This is applicable to multiple SIM/SAM (secure access module) configurations.

0-C     D-L     M-R     S-Z