|Category||Memory => Flash|
|Description||1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|Company||Advanced Micro Devices, Inc.|
|Datasheet||Download AM29F010-1 datasheet
1 Megabit x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory--Die Revision 1
s Single power supply operation ± 10% for read, erase, and program operations Simplifies system-level power requirements s High performance 120 ns maximum access time s Low power consumption 30 mA max active read current 50 mA max program/erase current <25 µA typical standby current s Flexible sector architecture Eight uniform sectors Any combination of sectors can be erased Supports full chip erase s Sector protection Hardware-based feature that disables/reenables program and erase operations in any combination of sectors Sector protection/unprotection can be implemented using standard PROM programming equipment s Embedded Algorithms Embedded Erase algorithm automatically pre-programs and erases the chip or any combination of designated sector Embedded Program algorithm automatically programs and verifies data at specified address s Minimum 100,000 program/erase cycles guaranteed s Compatible with JEDEC standards Pinout and software compatible with single-power-supply flash Superior inadvertent write protection s Data Polling and Toggle Bits Provides a software method of detecting program or erase cycle completion s Tested to datasheet specifications at temperature s Quality and reliability levels equivalent to standard packaged components
The Am29F010 in Known Good Die (KGD) form a 1 Mbit, 5.0 Volt-only Flash memory. AMD defines KGD as standard product in die form, tested for functionality and speed. AMD KGD products have the same reliability and quality as AMD products in packaged form. Am29F010 Features The Am29F010 device is organized as eight uniform sectors of 16 Kbytes each for flexible erase capability. This device is designed to be programmed in-system with the standard system 5.0 Volt V CC supply. A power supply providing 12.0 Volt PP is not required for program or erase operations. The Am29F010 in KGD form offers access times 90 ns and 120 ns, allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has separate chip enable (CE#), write enable (WE#) and output enable (OE) controls. The device requires only a single 5.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state machine that controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from other Flash or EPROM devices. Device programming occurs by executing the program command sequence. This invokes the Embedded
Program algorithm--an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. Device erasure occurs by executing the erase command sequence. This invokes the Embedded Erase algorithm--an internal algorithm that automatically preprograms the array (if it is not already programmed) before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margin. The host system can detect whether a program or erase operation is complete by reading the DQ7 (Data# Polling) and DQ6 (toggle) status bits. After a program or erase cycle has been completed, the device is ready to read array data or accept another command. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is erased when shipped from the factory. The hardware data protection measures include a low VCC detector automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memory, and is implemented using standard EPROM programmers. The system can place the device into the standby mode. Power consumption is greatly reduced in this mode.
Refer to the Am29F010 data sheet, publication number 16736, for full electri cal specifications for the Am29F010 in KGD form.
Family Part Number Speed Option (VCC ± 10%) Max Access Time, tACC (ns) Max CE# Access, tCE (ns) Max OE# Access, tOE (ns) Am29F010 KGDOrientation relative to leading edge of tape and reel
|Some Part number from the same manufacture Advanced Micro Devices, Inc.|
|AM29F010-120DGE1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DGI1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DPC1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DPE1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DPI1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DTC1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DTE1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DTI1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DWC1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
|AM29F010-120DWE1 1 Megabit ( 128 K X 8-bit ) CMOS 5.0 Volt-only, Uniform Sector Flash Memory-die Revision 1|
AM28F256A-70FC : 256 Kilobit ( 32 K X 8-bit ) CMOS 12.0 Volt, Bulk Erase Flash Memory With Embedded Algorithms
AM29F200AT-120DWC1 : 2 Megabit ( 256 K X 8-bit/128 K X 16-bit ) CMOS 5.0 Volt-only, Sectored Flash Memory-die Revision 1
AM29F800BB-120DPC1 : 8 Megabit ( 1 M X 8-bit/512 K X 16-bit ) CMOS 5.0 Volt-only, Boot Sector Flash Memory-die Revision 1
80188-10B : High Integration 8-bit Microprocessor
D163DT90VF : 16 Megabit (2 M x 8-bit/1 M x 16-bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory
AM29BDD160GB40APBK : 16 Megabit (1 M x 16-bit/512 K x 32-bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/write Flash Memory
AM29BDD160GT58APBI : 16 Megabit (1 M x 16-bit/512 K x 32-bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/write Flash Memory
AM29LV017D-90FI : 256 Megabit (16 M x 16-bit/32 M x 8-bit) Mirrorbittm 3.0 Volt-only Uniform Sector Flash Memory with Versatilei/otm Control
AM93L412ALC : 256 X 4 STANDARD SRAM, 75 ns, CDIP22 Specifications: Memory Category: SRAM Chip ; Density: 1 kbits ; Number of Words: 256 k ; Bits per Word: 4 bits ; Package Type: DIP, HERMETIC SEALED, CERAMIC, DIP-22 ; Pins: 22 ; Logic Family: TTL ; Supply Voltage: 5V ; Access Time: 75 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F)
Am29DL32 : 32 Megabit (4 M X 8-Bit/2 M X 16-Bit) Boot Sector (Advance Information).
CY7C147 : Memory Products. Automatic powerdown when deselected CMOS for optimum speed/power High speed 20 ns Low active power 550 mW Low standby power 110 mW TTLcompatible inputs and outputs Capable of withstanding greater than 2001V electrostatic discharge The CY6116A and CY6117A are high performance CMOS static RAMs orga nized as 2048 words by 8 bits. Easy memoryexpansionisprovidedbyanactive.
EDI7F233512V : Flash Modules. Organization = 2x512Kx32 ;; Speed (ns) = 80-150 ;; Volt = 3.3 ;; Package = SIMM-80 ;; Temp = ;;.
HN58X2402SFPIAG : . Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp. The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog and discrete devices, and memory chips.
HYMD525G726LS4 : 2 GB. 256Mx72 Bits Registered DDR Sdram Dimm. Hynix HYMD525G726(L)S4-K/H/L series is registered 184-pin double data rate Synchronous DRAM Dual In-Line Memory Modules (DIMMs) which are organized as 256Mx72 high-speed memory arrays. Hynix HYMD525G726(L)S4K/H/L series consists of eighteen stacked 128Mx4 DDR SDRAM in 400mil TSOP II packages a 184pin glass-epoxy substrate. Hynix HYMD525G726(L)S4-K/H/L.
KMM366S104CT : Unbuffered DIMM. = KMM366S104CT 1Mx64 Sdram Dimm Based on 1Mx16, 4K Refresh, 3.3V Synchronous DRAMs With SPD ;; Density(MB) = 8 ;; Organization = 1Mx64 ;; Bank/ Interface = 2B/LVTTL ;; Refresh = 4K/64ms ;; Speed = G8,GH,GL ;; #of Pin = 168 ;; Power = G ;; Component Composition = (1Mx16)x4+EEPROM ;; Production Status = Eol ;; Comments = PC100&PC66.
KMM390S2858AT : Registered DIMM. = KMM390S2858AT 128Mx72 Sdram Dimm With PLL & Register Based on Stacked 128Mx4, 4Banks 8K Ref., 3.3V Sdrams With SPD ;; Density(MB) = 1024 ;; Organization = 128Mx72 ;; Bank/ Interface = 4B/LVTTL ;; Refresh = 8K/64ms ;; Speed = 75 ;; #of Pin = 168 ;; Power = G ;; Component Composition = (128Mx4)x18+Drive ICx3+PLL+EEPROM ;; Production.
M381L6423BT1 : = M381L6423BT1 64M X 72 DDR Sdram 184pin Dimm Based on 32M X 8 ;; Density(MB) = 512 ;; Organization = 64Mx72 ;; Bank/ Interface = 4B/SSTL2 ;; Refresh = 8K/64ms ;; Speed = A0,A2,B0 ;; #of Pin = 184 ;; Power = C,l ;; Component Composition = (32Mx8)x18 ;; Production Status = Eol ;; Comments = Ecc.
M464S3323CN0 : SODIMM. = M464S3323CN0 32Mx64 Sdram Sodimm Based on STSOP2 16Mx8, 4Banks, 4K Refresh, 3.3V Sdrams With SPD ;; Density(MB) = 256 ;; Organization = 32Mx64 ;; Bank/ Interface = 4B/LVTTL ;; Refresh = 4K/64ms ;; Speed = 1H,1L ;; #of Pin = 144 ;; Power = C,l ;; Component Composition = (16Mx8)x16 ;; Production Status = Eol ;; Comments = -.
M5M5256DP : Lsis: 262144-bit (32768-word BY 8-bit) CMOS Static RAM. The is 262,144-bit CMOS static RAMs organized by 8-bits which is fabricated using high-performance 3 polysilicon CMOS technology. The use of resistive load NMOS cells and CMOS periphery results in a high density and low power static RAM. Stand-by current is small enough for battery back-up application. It is ideal for the memory systems which require.
MCM6343 : 256k X 15 Bit 3.3 V Asynchronous Fast Static RAM. The a 4,194,304bit static random access memory organized as 262,144 words of 16 bits. Static design eliminates the need for external clocks or timing strobes. The MCM6343 is equipped with chip enable (E), write enable (W), and output enable (G) pins, allowing for greater system flexibility and eliminating bus contention problems. Separate byte enable.
W27L010 : ->UV/EPROM. 128K X 8 Electrically Erasable EPROM. The is a high speed, low power consumption Electrically Erasable and Programmable Read Only Memory organized × 8 bits. It requires only one supply in the range 3.6V in normal read mode. The W27L010 provides an electrical chip erase function. High speed access time: 120/150 nS (max.) Read operating current: 10 mA (max.) Erase/Programming operating current:.
K7D161874B : 1Mx18 Organizations The K7D163674B and K7D161874B are 18,874,368 bit Synchronous Pipeline Burst Mode SRAM devices. They are organized as 524,288 words by 36 bits for K7D163674B and 1,048,576 words by 18 bits for K7D161874B, fabricated using Samsung's advanced CMOS technology..
AS5LC512K8DCJ-20/883C : 512K X 8 STANDARD SRAM, 20 ns, CDSO36. s: Memory Category: SRAM Chip ; Density: 4194 kbits ; Number of Words: 512 k ; Bits per Word: 8 bits ; Package Type: SOJ, CERAMIC, SOJ-36 ; Pins: 36 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 20 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F).
M25P80-VMC6G : 8M X 1 FLASH 2.7V PROM, PDSO8. s: Memory Category: Flash, PROM ; Density: 8389 kbits ; Number of Words: 8000 k ; Bits per Word: 1 bits ; Package Type: 4 X 3 MM, ROHS COMPLIANT, UFDFPN-8 ; Pins: 8 ; Logic Family: CMOS ; Data Rate: 75 MHz ; Operating Temperature: -40 to 85 C (-40 to 185 F).
70261L20PF8 : 16K X 16 DUAL-PORT SRAM, 20 ns, PQFP100. s: Memory Category: SRAM Chip ; Density: 262 kbits ; Number of Words: 16 k ; Bits per Word: 16 bits ; Package Type: TQFP, 14 X 14 MM, 1.40 MM HEIGHT, TQFP-100 ; Pins: 100 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 20 ns ; Operating Temperature: 0 to 70 C (32 to 158 F).